1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Adding phono input to a 37-650X
islesailor
Junior Member
**
Posts: 3
Threads: 1
Joined: May 2019
City: Fort Pierce State, Province, Country: Florida
#2

05-20-2019, 08:46 PM
I added a jack for a bluetooth reciever to my 37-650x, it works fine. Should work for your phono. Mount a jack aand a spdt on the rear of your chassis. Since the radio is mono you need to combine the stereo channels. Connect a 1K resistor to each side of the jack. Connect the 1K resistors together and to a 1 Meg resistor. Connect the 1 Meg to ground. Connect the junction of the 2 1K and the 1 Meg to one side of the SPDT switch. Disconnect C33 (.01) from the junction of R31/R32. Connect C33 to the center terminal of the switch. Connect the other side of the switch to the place where you disconnected C33. Connect the third pin on the jack to ground.
Enjoy
Kelton
W4IND
(This post was last modified: 05-21-2019, 12:56 PM by islesailor.)
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
RE: Adding phono input to a 37-650X - by islesailor - 05-20-2019, 08:46 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70.  The trim around the base needs to be replaced.  If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration