Philco 200X

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco 200X

Radioroslyn
Phorum Expert

Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa

09-25-2019, 12:23 PM

I have a 200X that the top is missing the center section of veneer. Anyone have a pic or know what the grain orientation is for this section?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Philco 200X - by Radioroslyn - 09-25-2019, 12:23 PM

RE: Philco 200X - by Patrick - 09-25-2019, 12:55 PM

RE: Philco 200X - by Radioroslyn - 09-25-2019, 01:54 PM

RE: Philco 200X - by Nathan Slingerland - 09-25-2019, 04:50 PM

RE: Philco 200X - by Radioroslyn - 09-25-2019, 07:45 PM

RE: Philco 200X - by Nathan Slingerland - 09-26-2019, 01:30 AM

RE: Philco 200X - by OldRestorer - 09-30-2019, 10:23 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM

Who's Online

There are currently 1025 online users. [Complete List]
» 4 Member(s) | 1021 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me