Latest on the 37-650

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Latest on the 37-650

Bill Hutchinson
Member

Posts: 236
Threads: 30
Joined: Sep 2005
City: Minneapolis/St. Paul MN

02-22-2006, 06:39 PM

I think you need to start over aligning it. At least it squeals and howls at the low end and you get something worthwhile on the high end, that (to me) is a good thing, and it means you're on the right track.

Not having the instructions in front of me, and the alignment I did was about 6 years ago, I'm a little foggy on the details, but I think we can all smell sucess coming! Icon_smile

Don't give up!

Bill

Sent from my Pentium II on the AT&T Dial Network

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Latest on the 37-650 - by Robbie Roberts - 02-21-2006, 10:57 PM

[No subject] - by Bill Hutchinson - 02-22-2006, 06:39 PM

[No subject] - by Robbie Roberts - 02-22-2006, 06:41 PM

[No subject] - by Bill Hutchinson - 02-22-2006, 06:50 PM

[No subject] - by Chuck Schwark - 02-22-2006, 07:35 PM

[No subject] - by Robbie Roberts - 02-22-2006, 07:38 PM

[No subject] - by Chuck Schwark - 02-22-2006, 08:29 PM

[No subject] - by Robbie Roberts - 02-22-2006, 08:35 PM

[No subject] - by Steve Chambers - 02-22-2006, 08:44 PM

[No subject] - by Robbie Roberts - 02-22-2006, 08:47 PM

[No subject] - by Chuck Schwark - 02-22-2006, 09:00 PM

[No subject] - by Robbie Roberts - 02-23-2006, 12:56 AM

[No subject] - by Derek D - 02-23-2006, 01:33 AM

[No subject] - by Robbie Roberts - 02-23-2006, 01:40 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me