Latest on the 37-650

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Latest on the 37-650

Robbie Roberts
Member

Posts: 147
Threads: 28
Joined: Nov 2005

02-22-2006, 06:41 PM

Another concept which has just developed- When I did all the rewiring, I replaced the wires to the two RF cans.(The coils themselves are as original) Originally they were 20 or 22 ga solid, I replaced them with 20ga. stranded. Is it possible I increased the resistance there just enough to scramble up the lower(900 + below) BC bands, while still allowing 900 + up to pass through? Resistance issues seem to be the biggest issue I have been encountering with this radio.

Comments? Answers? Theories? Recipies?
Thanks!
Scott

Old Cars, Old Radios, Old Pipes and Young Women... What more is there?

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Latest on the 37-650 - by Robbie Roberts - 02-21-2006, 10:57 PM

[No subject] - by Bill Hutchinson - 02-22-2006, 06:39 PM

[No subject] - by Robbie Roberts - 02-22-2006, 06:41 PM

[No subject] - by Bill Hutchinson - 02-22-2006, 06:50 PM

[No subject] - by Chuck Schwark - 02-22-2006, 07:35 PM

[No subject] - by Robbie Roberts - 02-22-2006, 07:38 PM

[No subject] - by Chuck Schwark - 02-22-2006, 08:29 PM

[No subject] - by Robbie Roberts - 02-22-2006, 08:35 PM

[No subject] - by Steve Chambers - 02-22-2006, 08:44 PM

[No subject] - by Robbie Roberts - 02-22-2006, 08:47 PM

[No subject] - by Chuck Schwark - 02-22-2006, 09:00 PM

[No subject] - by Robbie Roberts - 02-23-2006, 12:56 AM

[No subject] - by Derek D - 02-23-2006, 01:33 AM

[No subject] - by Robbie Roberts - 02-23-2006, 01:40 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me