Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Olympic 6-608-110
#28

Actually, Jake, it is because of the orientation of the pulsing magnetic field on the wires. They run horizontally, and the antenna is vertical. its reception field is at 90 degrees to that which the lines create. It was inspired by an old drawing I saw in one of my books which advised orienting a long wire antenna at 90 degrees to any trolley lines which ran in front of your house. I considered the best way to accomplish thins in the least space, and decided on a vertically oriented antenna. It has the added advantage over a long wire in that it is omni-directional, and receives equally well from all directions. It is really an ideal antenna for my use; it works well for all directions, and takes very little space, just clearance above it, and it minimizes the interference from the power lines. Much more practical for my use than a long wire. Everybody's Radio Manual, page 141...

[Image: https://66.media.tumblr.com/3f86a67662ef...b7096a.jpg]

This is a very useful old book, and has a whole section on how to eliminate interference from your receiver.


Messages In This Thread
Olympic 6-608-110 - by mikethedruid - 10-17-2019, 12:11 AM
RE: Olympic 6-608-110 - by mikethedruid - 10-18-2019, 10:56 PM
RE: Olympic 6-608-110 - by Paul Philco322 - 10-19-2019, 08:22 AM
RE: Olympic 6-608-110 - by mikethedruid - 10-19-2019, 12:08 PM
RE: Olympic 6-608-110 - by Ron Ramirez - 10-19-2019, 03:21 PM
RE: Olympic 6-608-110 - by Jake Blake - 12-11-2019, 02:44 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-11-2019, 07:30 PM
RE: Olympic 6-608-110 - by Jake Blake - 12-11-2019, 08:09 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-14-2019, 06:21 PM
RE: Olympic 6-608-110 - by Jake Blake - 12-14-2019, 06:27 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-14-2019, 06:32 PM
RE: Olympic 6-608-110 - by Paul Philco322 - 12-14-2019, 07:27 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-14-2019, 07:41 PM
RE: Olympic 6-608-110 - by jake wells - 12-15-2019, 05:54 AM
RE: Olympic 6-608-110 - by mikethedruid - 12-22-2019, 12:25 AM
RE: Olympic 6-608-110 - by mikethedruid - 12-26-2019, 05:29 PM
RE: Olympic 6-608-110 - by Jake Blake - 12-26-2019, 05:34 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-26-2019, 06:58 PM
RE: Olympic 6-608-110 - by Jake Blake - 12-26-2019, 08:04 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-31-2019, 06:25 PM
RE: Olympic 6-608-110 - by NostalgiaRadioTime - 12-31-2019, 10:19 PM
RE: Olympic 6-608-110 - by mikethedruid - 12-31-2019, 10:34 PM
RE: Olympic 6-608-110 - by Ron Ramirez - 01-01-2020, 09:26 AM
RE: Olympic 6-608-110 - by mikethedruid - 01-04-2020, 10:41 AM
RE: Olympic 6-608-110 - by Jake Blake - 01-04-2020, 10:58 AM
RE: Olympic 6-608-110 - by mikethedruid - 01-04-2020, 12:24 PM
RE: Olympic 6-608-110 - by Jake Blake - 01-04-2020, 12:40 PM
RE: Olympic 6-608-110 - by mikethedruid - 01-04-2020, 04:13 PM
RE: Olympic 6-608-110 - by Jake Blake - 01-04-2020, 08:10 PM
RE: Olympic 6-608-110 - by Paul Philco322 - 01-04-2020, 09:37 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM
54C Complete Teardown/Rebuild
Richard, Had grabbed it already but thank you just the same.  I find myself wanting to find some way to block out the...glyphmon — 12:03 AM
54C Complete Teardown/Rebuild
Hello roy, here is a link to the schematic . Sincerely Richardradiorich — 11:54 PM
54C Complete Teardown/Rebuild
Richard, The Silvertone 2014 also is a transformerless set, so I am incorporating a 1:1 600 ohm audio isolation transfo...glyphmon — 11:37 PM
Preliminary work on wife's Silvertone 2014
Did an alignment today which was interesting.  IF alignment went great, almost all was already spot-on.  Adjusting on th...glyphmon — 11:35 PM
54C Complete Teardown/Rebuild
The main problem with adding a Bluetooth input is that this set lacks a traditional power transformer to isolate it from...radiorich — 11:19 PM
54C Cabinet Refinish
I started stripping this cabinet before it got super chilly out because I knew I wasn't going to be able to work on ...glyphmon — 11:18 PM
54C Complete Teardown/Rebuild
While I'm waiting to wrap up the final steps on my wife's Silvertone 2014, I started disassembly on the next project.  O...glyphmon — 11:07 PM
Preliminary work on wife's Silvertone 2014
Hello roy, that great news glad it worked out for you !! Sincerely Richardradiorich — 10:50 PM
Preliminary work on wife's Silvertone 2014
Safety caps arrived today.  Soldered one in and had a successful first power-up.  No magic smoke escaped and it tunes in...glyphmon — 09:53 PM

[-]
Who's Online
There are currently no members online.

>