Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 41-250
#2

Hello and welcome!

Don't worry about your set having a 25 cycle power transformer; it will work just fine on 60 cycle AC. I don't know when Philco stopped making sets in the USA designed to operate on 25 cycle AC. They made them at least up to and including the 1942 models; my 1946 Philco parts catalog lists 25 cycle transformers for some 1942 models.

Some of those Philco tenite escutcheons have a gold stripe, as yours has. My 41-610 has a gold stripe as yours does. The reproductions do not have the gold stripe, however.

I find it very odd that the PHILCO decal would be on the escutcheon itself, I've seen quite a few 41-250 sets, and every one had the PHILCO decal above the dial, on the wood and not the escutcheon.

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Philco 41-250 - by andyjon100 - 01-21-2011, 05:56 PM
RE: Philco 41-250 - by GACTVDX - 09-17-2014, 08:57 PM
Re: Philco 41-250 - by Ron Ramirez - 01-21-2011, 07:25 PM
Re: Philco 41-250 - by andyjon100 - 01-21-2011, 10:45 PM
Re: Philco 41-250 - by andyjon100 - 01-21-2011, 10:50 PM
Re: Philco 41-250 - by gary rabbitt - 01-22-2011, 03:13 AM
Re: Philco 41-250 - by Ron Ramirez - 01-22-2011, 08:57 AM
Re: Philco 41-250 - by Ron Ramirez - 01-22-2011, 09:15 AM
Re: Philco 41-250 - by andyjon100 - 01-22-2011, 01:09 PM
Re: Philco 41-250 - by gary rabbitt - 01-22-2011, 01:48 PM
Re: Philco 41-250 - by Ron Ramirez - 01-22-2011, 02:55 PM
Re: Philco 41-250 - by andyjon100 - 01-22-2011, 03:19 PM
Re: Philco 41-250 - by Art Hoch - 02-04-2011, 01:09 PM
Re: Philco 41-250 - by andyjon100 - 02-05-2011, 02:00 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 809 online users. [Complete List]
» 1 Member(s) | 808 Guest(s)
Avatar

>