Fairbanks Morse model 56

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Fairbanks Morse model 56

Radioroslyn
Phorum Expert

Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa

#16

02-23-2020, 01:59 AM

Don't think I've ever seen a metal standard based tube, only on the self centering tubes (octals). Pin 1 is always the heater. Have seen some tubes that have had a sprayed on coating but I don't remember if it has any connection to anything.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Fairbanks Morse model 56 - by Stall-U-Rated - 11-19-2019, 01:51 AM

RE: Fairbanks Morse model 56 - by Radioroslyn - 11-19-2019, 10:30 AM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 11-19-2019, 06:38 PM

RE: Fairbanks Morse model 56 - by Radioroslyn - 11-19-2019, 09:15 PM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 11-21-2019, 01:46 AM

RE: Fairbanks Morse model 56 - by Eliot Ness - 11-21-2019, 02:27 AM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 11-21-2019, 11:48 PM

RE: Fairbanks Morse model 56 - by Eliot Ness - 11-22-2019, 01:06 AM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 11-22-2019, 02:15 AM

RE: Fairbanks Morse model 56 - by Steve Davis - 11-22-2019, 07:46 AM

RE: Fairbanks Morse model 56 - by Eliot Ness - 11-22-2019, 11:31 AM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 11-24-2019, 01:54 AM

RE: Fairbanks Morse model 56 - by Steve Davis - 11-24-2019, 12:31 PM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 12-05-2019, 10:00 PM

RE: Fairbanks Morse model 56 - by mikethedruid - 02-23-2020, 01:23 AM

RE: Fairbanks Morse model 56 - by Radioroslyn - 02-23-2020, 01:59 AM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 02-23-2020, 02:06 AM

RE: Fairbanks Morse model 56 - by Stall-U-Rated - 02-27-2020, 12:01 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
462ron
It’s on the bottom of the homepage of our Philcoradio.com homepage! Ron462ron — 07:20 AM
Model 70 Cabinet Trim
Steve might have some trim left. Not sure he is making anything.morzh — 06:12 AM
Model 70 Cabinet Trim
Hello musar, First all welcome to the forum and yes that is true that steve stopped making trim . Sincerely Richar...radiorich — 12:13 AM
Model 70 Cabinet Trim
I have recently come into possession of a Model 70. The trim around the base needs to be replaced. If this were years ...musar — 12:07 AM
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM

Who's Online

There are currently 254 online users. [Complete List]
» 1 Member(s) | 253 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me