46-250 125

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

46-250 125

Eric Adams
Phorum Expert

Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida

05-04-2020, 10:30 PM

Hi everyone! I hope everyone is well and staying safe.
I have a problem that I have never run into before. Although it does sound like I've said that before. Anyway, I replaced all the caps, checked and replaced any resistors over 20% out. All the tubes check good and it has been aligned. Here's my problem: with the original loop antenna (it has continuity) the only thing I can pick up is my SStran, about 8 feet away. If I connect my long wire to the antenna connector it sounds great and picks up all local stations.
Any ideas where to look?

www.radiomuseum.org_ 46-250 Transitone Code 125.pdf Size: 94.89 KB Downloads: 226

Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

46-250 125 - by Eric Adams - 05-04-2020, 10:30 PM

RE: 46-250 125 - by LarryFS - 05-04-2020, 10:53 PM

RE: 46-250 125 - by radiodale - 05-04-2020, 10:54 PM

RE: 46-250 125 - by Eric Adams - 05-04-2020, 11:02 PM

RE: 46-250 125 - by morzh - 05-04-2020, 11:28 PM

RE: 46-250 125 - by Eric Adams - 05-04-2020, 11:44 PM

RE: 46-250 125 - by RodB - 05-05-2020, 08:37 AM

RE: 46-250 125 - by Radioroslyn - 05-05-2020, 09:49 AM

RE: 46-250 125 - by Eric Adams - 05-05-2020, 11:58 AM

RE: 46-250 125--Fixed!!! - by Eric Adams - 05-05-2020, 02:50 PM

RE: 46-250 125 - by Radioroslyn - 05-05-2020, 03:10 PM

RE: 46-250 125 - by RodB - 05-05-2020, 04:33 PM

RE: 46-250 125 - by Eric Adams - 05-05-2020, 04:37 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM

Who's Online

There are currently 420 online users. [Complete List]
» 1 Member(s) | 419 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me