1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
High voltage readings
Tom45acp
Junior Member
**
Posts: 26
Threads: 9
Joined: Dec 2019
City: Shinnston State, Province, Country: WV
#3

05-08-2020, 07:17 PM
This is a 2 section resistor, one section is 90 ohms with 5.6 volts across it and the second section is 210 ohms with 20 volts across it.
Sometimes I wonder whether the world is being run by smart people who are putting us on or by imbeciles who really mean it.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
High voltage readings - by Tom45acp - 05-08-2020, 05:37 PM
RE: High voltage readings - by gregb - 05-08-2020, 05:50 PM
RE: High voltage readings - by Tom45acp - 05-08-2020, 07:17 PM
RE: High voltage readings - by Radioroslyn - 05-08-2020, 08:44 PM
RE: High voltage readings - by Tom45acp - 05-09-2020, 04:00 PM
RE: High voltage readings - by Steve Davis - 05-09-2020, 05:57 PM
RE: High voltage readings - by morzh - 05-09-2020, 06:31 PM
RE: High voltage readings - by Tom45acp - 05-10-2020, 08:29 PM
RE: High voltage readings - by morzh - 05-10-2020, 09:01 PM
RE: High voltage readings - by Tom45acp - 05-11-2020, 08:59 AM
RE: High voltage readings - by morzh - 05-11-2020, 10:42 AM
RE: High voltage readings - by Tom45acp - 05-11-2020, 06:44 PM
RE: High voltage readings - by morzh - 05-11-2020, 08:45 PM
RE: High voltage readings - by Tom45acp - 05-12-2020, 08:44 AM
RE: High voltage readings - by RodB - 05-12-2020, 09:19 AM
RE: High voltage readings - by morzh - 05-12-2020, 10:18 AM
RE: High voltage readings - by Tom45acp - 05-12-2020, 12:12 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration