1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
1935 623F
tigercat
Junior Member
**
Posts: 7
Threads: 1
Joined: May 2020
City: West Point State, Province, Country: Iowa
#4

05-18-2020, 05:03 PM
So both C+(3 volt and 7.5 volt) are connected to B-.

Thanks to you both for the info.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
1935 623F - by tigercat - 05-18-2020, 01:04 PM
RE: 1935 623F - by Radioroslyn - 05-18-2020, 01:24 PM
RE: 1935 623F - by RodB - 05-18-2020, 02:00 PM
RE: 1935 623F - by tigercat - 05-18-2020, 05:03 PM
RE: 1935 623F - by Radioroslyn - 05-18-2020, 08:42 PM
RE: 1935 623F - by tigercat - 05-18-2020, 09:06 PM
RE: 1935 623F - by tigercat - 06-19-2020, 02:36 PM
RE: 1935 623F - by Radioroslyn - 06-19-2020, 03:36 PM
RE: 1935 623F - by tigercat - 07-15-2020, 05:08 PM
RE: 1935 623F - by Radioroslyn - 07-16-2020, 06:22 PM
RE: 1935 623F - by tigercat - 07-18-2020, 09:46 AM
RE: 1935 623F - by Radioroslyn - 07-18-2020, 10:04 AM
RE: 1935 623F - by tigercat - 07-18-2020, 12:04 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration