1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 38-3 hates me
DuMont
Junior Member
**
Posts: 40
Threads: 10
Joined: Nov 2018
City: Dallas State, Province, Country: Texas
#1

05-18-2020, 06:11 PM
This is something I've never encountered.   I have my signal generator and frequency counter and output meter set up...and I can do the IF (470 at dial position 580) with no trouble.
When I move to begin the RF, the signal from the generator doesn't come through. All I get is an annoying buzz. (which, oddly enough, I can peak by turning RF adjustors)
Anyone have any ideas???
Thanks in advance!
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 38-3 hates me - by DuMont - 05-18-2020, 06:11 PM
RE: Philco 38-3 hates me - by radiodale - 05-18-2020, 07:32 PM
RE: Philco 38-3 hates me - by DuMont - 05-18-2020, 07:52 PM
RE: Philco 38-3 hates me - by morzh - 05-18-2020, 08:49 PM
RE: Philco 38-3 hates me - by DuMont - 05-18-2020, 08:57 PM
RE: Philco 38-3 hates me - by David - 05-19-2020, 10:05 AM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 10:24 AM
RE: Philco 38-3 hates me - by David - 05-19-2020, 04:40 PM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 04:52 PM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 06:43 PM
RE: Philco 38-3 hates me - by DuMont - 05-19-2020, 07:24 PM
RE: Philco 38-3 hates me - by Tim Tress - 05-24-2020, 09:25 PM
RE: Philco 38-3 hates me - by RodB - 05-25-2020, 09:02 AM
RE: Philco 38-3 hates me - by captainclock1988 - 05-27-2020, 12:17 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM

[-]
Who's Online
There are currently 1070 online users. [Complete List]
» 3 Member(s) | 1067 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration