Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 90 weak high end
#6

Just for grins hook your ant up to the grid cap of the 24A mixer tube. Does this improve the situation?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Model 90 weak high end - by skykng - 06-09-2020, 06:42 PM
RE: Model 90 weak high end - by Radioroslyn - 06-10-2020, 12:28 PM
RE: Model 90 weak high end - by Phlogiston - 06-10-2020, 12:38 PM
RE: Model 90 weak high end - by skykng - 06-10-2020, 05:06 PM
RE: Model 90 weak high end - by skykng - 06-10-2020, 06:16 PM
RE: Model 90 weak high end - by Radioroslyn - 06-10-2020, 07:42 PM
RE: Model 90 weak high end - by skykng - 06-10-2020, 09:27 PM
RE: Model 90 weak high end - by Tim Tress - 07-05-2020, 04:41 PM
RE: Model 90 weak high end - by skykng - 07-05-2020, 06:01 PM
RE: Model 90 weak high end - by tubejockey - 08-21-2020, 03:21 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently no members online.

>