1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
1935 Philco 144
PhilcoPhan1936
Jeff W.
******
Posts: 751
Threads: 91
Joined: Nov 2015
City: Jonesboro State, Province, Country: AR
#11

07-20-2020, 08:40 PM
I took the time to sit down and compare coils and part numbers. With the exception of the first IF and the wave trap, all coils parts numbers are the same, and the coil values are listed on the 44 schematic. So now I need to go through and measure every coil and make sure no other coils are fried From the lightning strike. Icon_eek
Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
1935 Philco 144 - by PhilcoPhan1936 - 05-23-2020, 12:02 AM
RE: 1935 Philco 144 - by RodB - 05-23-2020, 09:19 AM
RE: 1935 Philco 144 - by morzh - 05-23-2020, 11:07 AM
RE: 1935 Philco 144 - by PhilcoPhan1936 - 05-23-2020, 12:14 PM
RE: 1935 Philco 144 - by Scott D - 05-23-2020, 04:22 PM
RE: 1935 Philco 144 - by morzh - 05-23-2020, 04:40 PM
RE: 1935 Philco 144 - by Scott D - 05-23-2020, 04:56 PM
RE: 1935 Philco 144 - by PhilcoPhan1936 - 07-20-2020, 07:34 PM
RE: 1935 Philco 144 - by Radioroslyn - 07-20-2020, 08:22 PM
RE: 1935 Philco 144 - by PhilcoPhan1936 - 07-20-2020, 08:36 PM
RE: 1935 Philco 144 - by PhilcoPhan1936 - 07-20-2020, 08:40 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM

[-]
Who's Online
There are currently 929 online users. [Complete List]
» 2 Member(s) | 927 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration