60-505 no audio

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

60-505 no audio

Ram
Junior Member

Posts: 13
Threads: 2
Joined: Feb 2011

02-14-2011, 09:23 PM

Have a meter, will test the resistance of the coils, didn't think of coils.
Cap's don't have any outward bad indications, such as swelling, leaking, or cracks or even discoloration. All have both ends with the wires still attached as well. Took a chance powering up with the cap's. Will have to test them too.

Have been e-mailing Mark, he does not stock the part number to replace my dial. Will have to drill the rivets and scan into computer for re-construction then make new decal myself.

Have looked at Retro-Tronics previous to posting. Have only seen back boards. Will e-mail them and see if they have a speaker board or even be able to just sell some hard stock.

And that stuck tube, I don't want to use too much force on that to trash the socket as you have mentioned. Will have to work it some more and hope it starts to move.

Thanks,
Gary

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

60-505 no audio - by Ram - 02-13-2011, 03:00 PM

Re: 60-505 no audio - by Ron Ramirez - 02-14-2011, 10:29 AM

Re: 60-505 no audio - by Ram - 02-14-2011, 09:23 PM

Re: 60-505 no audio - by Ram - 02-21-2011, 06:29 PM

Re: 60-505 no audio - by Ron Ramirez - 02-22-2011, 09:54 PM

Re: 60-505 no audio - by Ram - 02-24-2011, 09:59 PM

Re: 60-505 no audio - by Ron Ramirez - 03-03-2011, 09:25 AM

Re: 60-505 no audio - by Ram - 04-05-2011, 07:48 PM

Re: 60-505 no audio - by Ram - 04-09-2011, 07:37 AM

Re: 60-505 no audio - by 7estatdef - 04-09-2011, 08:59 AM

Re: 60-505 no audio - by Ram - 04-19-2011, 09:52 PM

Re: 60-505 no audio - by 7estatdef - 04-20-2011, 09:00 PM

Re: 60-505 no audio - by Ram - 04-30-2011, 08:01 PM

Re: 60-505 no audio - by 7estatdef - 05-01-2011, 02:34 PM

Re: 60-505 no audio - by Ram - 05-02-2011, 07:52 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2324 online users. [Complete List]
» 2 Member(s) | 2322 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me