Model 71 oscillator

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Model 71 oscillator

WB5NEN
Junior Member

Posts: 13
Threads: 1
Joined: Aug 2020
City: Corrales State, Province, Country: NM

#28

09-15-2020, 12:00 PM

Terry,

I have not rewound the feedback coil, because it shows good continuity. I have, however, thought about rewinding it just to get a few extra turns in a (probably foolish) attempt to provide more feedback. Once it quits again, and if I find voltages are still what they should be on the tube, I will also check the coil for continuity.

But if this sounds like I’m taking the wrong path, let me know!

Richard

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Model 71 oscillator - by WB5NEN - 09-06-2020, 02:17 PM

RE: Model 71 oscillator - by Steve Davis - 09-06-2020, 10:16 PM

RE: Model 71 oscillator - by Radioroslyn - 09-07-2020, 08:39 AM

RE: Model 71 oscillator - by WB5NEN - 09-07-2020, 05:16 PM

RE: Model 71 oscillator - by WB5NEN - 09-07-2020, 07:32 PM

RE: Model 71 oscillator - by Radioroslyn - 09-07-2020, 07:53 PM

RE: Model 71 oscillator - by WB5NEN - 09-07-2020, 10:15 PM

RE: Model 71 oscillator - by WB5NEN - 09-08-2020, 01:57 PM

RE: Model 71 oscillator - by Radioroslyn - 09-08-2020, 07:58 PM

RE: Model 71 oscillator - by Steve Davis - 09-08-2020, 11:47 PM

RE: Model 71 oscillator - by WB5NEN - 09-09-2020, 04:19 PM

RE: Model 71 oscillator - by Radioroslyn - 09-09-2020, 06:57 PM

RE: Model 71 oscillator - by RodB - 09-09-2020, 07:00 PM

RE: Model 71 oscillator - by Radioroslyn - 09-09-2020, 08:49 PM

RE: Model 71 oscillator - by WB5NEN - 09-09-2020, 10:18 PM

RE: Model 71 oscillator - by Radioroslyn - 09-10-2020, 08:07 AM

RE: Model 71 oscillator - by WB5NEN - 09-10-2020, 08:50 AM

RE: Model 71 oscillator - by RodB - 09-10-2020, 08:57 AM

RE: Model 71 oscillator - by Radioroslyn - 09-10-2020, 10:34 AM

RE: Model 71 oscillator - by rfeenstra - 09-10-2020, 04:46 PM

RE: Model 71 oscillator - by WB5NEN - 09-10-2020, 10:43 PM

RE: Model 71 oscillator - by rfeenstra - 09-11-2020, 09:38 AM

RE: Model 71 oscillator - by WB5NEN - 09-11-2020, 10:07 AM

RE: Model 71 oscillator - by rfeenstra - 09-11-2020, 12:54 PM

RE: Model 71 oscillator - by rfeenstra - 09-11-2020, 01:05 PM

RE: Model 71 oscillator - by WB5NEN - 09-14-2020, 06:58 PM

RE: Model 71 oscillator - by Radioroslyn - 09-15-2020, 09:46 AM

RE: Model 71 oscillator - by WB5NEN - 09-15-2020, 12:00 PM

RE: Model 71 oscillator - by WB5NEN - 09-18-2020, 07:29 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me