1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco model 52-944
RodB
Phorum Expert
*****
Posts: 1,135
Threads: 46
Joined: Feb 2015
City: Roseville, MN
#7

09-23-2020, 09:05 AM
BTW Rick, I looked at the schematic a little closer last night and L2 is a rf transformer, not the oscillator coil like I previously said. You're on the right track. The 16" antenna is bypassing the rf amplifier and feeding the signal to the mixer/oscillator. Have you tried a different 12AU6? Check out C6 at 100pf. The signal is not getting from the rf amplifier to the oscillator. Yes, don't tweak any FM trimmers, you could loose your signal altogether.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco model 52-944 - by Ricky L. Adkins - 09-22-2020, 08:05 AM
RE: Philco model 52-944 - by RodB - 09-22-2020, 09:11 AM
RE: Philco model 52-944 - by Ricky L. Adkins - 09-22-2020, 12:12 PM
RE: Philco model 52-944 - by Ricky L. Adkins - 09-22-2020, 08:07 PM
RE: Philco model 52-944 - by RodB - 09-22-2020, 11:16 PM
RE: Philco model 52-944 - by Ricky L. Adkins - 09-23-2020, 12:01 AM
RE: Philco model 52-944 - by RodB - 09-23-2020, 09:05 AM
RE: Philco model 52-944 - by Ricky L. Adkins - 09-23-2020, 11:48 PM
RE: Philco model 52-944 - by Ricky L. Adkins - 09-24-2020, 10:59 PM
RE: Philco model 52-944 - by RodB - 09-25-2020, 08:46 AM
RE: Philco model 52-944 - by Ricky L. Adkins - 09-28-2020, 09:24 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Another amp build - here I go again!
Sweet! I actually have a Dyba Mark 4 that I had been running with 6L6s with no mods. seemed to my 14-year-old head a...MrFixr55 — 12:57 AM
PT-6 finished!!
Hi Gang, Tube heaters are not "Ohmic" devices (that maintain specified resistance over wide temperature, c...MrFixr55 — 12:03 AM
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration