1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco 42-350 Issues
captainclock1988
Senior Member
****
Posts: 325
Threads: 34
Joined: Dec 2019
City: Elkhart State, Province, Country: Indiana
#11

10-03-2020, 05:59 PM
All the parts are there for the phenolic board it's just whether or not they can be glued back together and stay glued. 

There's a spring and metal clip holding part of the phenolic board into place that I can't seem to get to come loose, that's what's holding up the works right now, and that spring is what causes the push buttons to spring back out when you push another button in.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Philco 42-350 Issues - by captainclock1988 - 10-02-2020, 05:57 PM
RE: Philco 42-350 Issues - by morzh - 10-02-2020, 07:09 PM
RE: Philco 42-350 Issues - by radiodale - 10-02-2020, 09:01 PM
RE: Philco 42-350 Issues - by morzh - 10-02-2020, 10:20 PM
RE: Philco 42-350 Issues - by captainclock1988 - 10-03-2020, 08:45 AM
RE: Philco 42-350 Issues - by morzh - 10-03-2020, 11:46 AM
RE: Philco 42-350 Issues - by captainclock1988 - 10-03-2020, 01:53 PM
RE: Philco 42-350 Issues - by morzh - 10-03-2020, 02:16 PM
RE: Philco 42-350 Issues - by rfeenstra - 10-03-2020, 02:21 PM
RE: Philco 42-350 Issues - by morzh - 10-03-2020, 02:33 PM
RE: Philco 42-350 Issues - by captainclock1988 - 10-03-2020, 05:59 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Electrolytic restuffing/internals
Look here: Philco-F676-124 Vlad95 — 08:02 PM
PT-6 finished!!
Well the 35Z3 doesn't have a tap on the tube heater for a pilot light, so in this set they have the dial lamp paralleled...Arran — 06:21 PM
Electrolytic restuffing/internals
Thanks. I think I try to cut this as suggested. I don’t have a lathe, but I do have a tap and die set. I am going to see...bridkarl — 04:46 PM
Another amp build - here I go again!
Hey all! Well, I guess that with what I learned from my last build, it's time to move up the ladder another rung and tak...TV MAN — 04:38 PM
Electrolytic restuffing/internals
There are various ways to handle this, one is to cut near just above that rolled in area is near the bottom, using the r...Arran — 04:36 PM
philco predicta
If you have a television signal generator (a must-have for TV repair) and an oscilloscope (the same), then this problem ...RadioSvit — 04:23 PM
HiFi (Chifi) tube amp build - but my own design.
Thanks Rod for the offer but I don't think those would work. There's some differences in the sizing and mounting holes b...TV MAN — 03:13 PM
philco predicta
Bob Anderson (Bandersontv) on Youtube would be the go-to guy on these. Lots of good videos. I don't know what model you ...TV MAN — 03:02 PM
Electrolytic restuffing/internals
I have an issue on a non-Philco radio which I expect to run into on a whole set of Philcos and others. I have an 8mf ...bridkarl — 01:17 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. I thought about it and decided to put it up in the arch support. I was looking at the chassis and didn't ...Stormlord5500 — 06:24 AM

[-]
Who's Online
There are currently 1067 online users. [Complete List]
» 3 Member(s) | 1064 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration