1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Television

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Craftsman RC200 resto
TV MAN
Phorum Expert
*****
Posts: 1,205
Threads: 84
Joined: Jan 2014
City: Annapolis, IL State, Province, Country: USA
#17

12-03-2020, 11:18 PM
I got the audio section recapped. I was doing some tests and saw the cathode resistor boiling wax, so I stuck my meter on the G1 and saw 18v on one tube and 30v on the other. Suppose to be 0v, so it was a bit high. This completes the recapatitation of this TV, unless I need to go after some mica caps or a paper cap hiding somewhere (like the yoke). So, now to the troubleshooting. I want to get the BK1077 running so I can hopefully isolate the problem(s). 

   

Thanks for the advices MrFixr. I think the tube is secure. If it did fall, it's carpeted and would likely just snap the neck, which I dont want either. Kinda getting hard to find good picture tubes anymore.
If I could find the place called "Somewhere", I could find "Anything" Icon_confused

Tim

Jesus cried out and said, "Whoever believes in me , believes not in me but in him who sent me" John 12:44
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Craftsman RC200 resto - by TV MAN - 12-25-2018, 05:41 PM
RE: Craftsman RC200 resto - by Paul Philco322 - 12-25-2018, 06:34 PM
RE: Craftsman RC200 resto - by Arran - 12-30-2018, 05:47 PM
RE: Craftsman RC200 resto - by TV MAN - 01-06-2019, 12:29 AM
RE: Craftsman RC200 resto - by TV MAN - 01-07-2019, 12:38 AM
RE: Craftsman RC200 resto - by TV MAN - 01-29-2019, 02:22 PM
RE: Craftsman RC200 resto - by TV MAN - 02-08-2019, 01:06 PM
RE: Craftsman RC200 resto - by KCMike - 02-08-2019, 01:15 PM
RE: Craftsman RC200 resto - by TV MAN - 02-09-2019, 03:39 PM
RE: Craftsman RC200 resto - by Arran - 02-10-2019, 02:39 AM
RE: Craftsman RC200 resto - by TV MAN - 02-11-2019, 09:38 PM
RE: Craftsman RC200 resto - by TV MAN - 07-04-2019, 10:43 AM
RE: Craftsman RC200 resto - by TV MAN - 03-13-2020, 09:23 PM
RE: Craftsman RC200 resto - by TV MAN - 03-16-2020, 02:12 PM
RE: Craftsman RC200 resto - by TV MAN - 11-25-2020, 09:06 PM
RE: Craftsman RC200 resto - by MrFixr55 - 11-28-2020, 12:30 AM
RE: Craftsman RC200 resto - by TV MAN - 12-03-2020, 11:18 PM
RE: Craftsman RC200 resto - by TV MAN - 12-13-2020, 04:21 PM
RE: Craftsman RC200 resto - by TV MAN - 12-31-2020, 02:46 PM
RE: Craftsman RC200 resto - by morzh - 12-31-2020, 04:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2033 online users. [Complete List]
» 1 Member(s) | 2032 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Television