Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 40-180 Chassis Restore
#1

Beginning the journey of restoring my 40-180 which was given to me by my grandparents years ago. As many know, the alignment procedure references the infamous loktal adapter that allows you to easily connect a VTVM for the procedure. I did notice instructions also mention you can connect the VTVM to the plate and socket (assuming ground) pins of one of the 41 tubes. Just curious if anyone had completed the procedure using this method?  Also curious it it would also be feasible to just connect a VTVM across the voice coil?  I’m not close to being ready to align the set yet, but thought I’d ask the question as I’ve read about a lot of different approaches from connecting leads to the appropriate pins of the 7C6 to simply “listening” for the best tone level from the signal generator.

Thanks!

Vince

Vinny
Greensburg, IN

"We don't care what you do...just don't electrocute yourself or burn the house down."
-My Parents


Messages In This Thread
Philco 40-180 Chassis Restore - by unclevinny86 - 02-15-2021, 09:28 PM
RE: Philco 40-180 Chassis Restore - by rfeenstra - 02-20-2021, 12:26 AM
RE: Philco 40-180 Chassis Restore - by morzh - 02-21-2021, 03:03 PM
RE: Philco 40-180 Chassis Restore - by rfeenstra - 02-21-2021, 03:23 PM
RE: Philco 40-180 Chassis Restore - by 462ron - 02-22-2021, 08:56 AM
RE: Philco 40-180 Chassis Restore - by morzh - 02-22-2021, 10:32 AM
RE: Philco 40-180 Chassis Restore - by morzh - 02-27-2021, 02:46 PM
RE: Philco 40-180 Chassis Restore - by Arran - 03-10-2021, 12:09 AM
RE: Philco 40-180 Chassis Restore - by RodB - 03-10-2021, 10:11 AM
RE: Philco 40-180 Chassis Restore - by morzh - 03-14-2021, 10:48 PM
RE: Philco 40-180 Chassis Restore - by tbone - 03-15-2021, 08:03 PM
RE: Philco 40-180 Chassis Restore - by OZ4 - 03-15-2021, 09:32 PM
RE: Philco 40-180 Chassis Restore - by morzh - 03-22-2021, 10:24 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco Model 38-7: what caps & resistors do fail typically?
Since you stated earlier, you have a console 38-7XX.  They also had a 38-7T (table), and 38-7CS (chairside).  A very nic...GarySP — 01:18 PM
Part numbers to model cross
That I wouldn't know, but sometimes the radio document itself shows one, same as the capacitor cans' etc pinouts.morzh — 12:46 PM
Part numbers to model cross
Thank you morzh, that is exactly what I was looking for. Now , is there some where that shows pinouts for Philco power ...Jim Dutridge — 11:37 AM
Restoration of the Canadian General Electric A-87
Thanks for your help Michael. In fact, this video is only an intermediate result. Later I had to apply another tinting l...RadioSvit — 09:01 AM
Restoration of the Canadian General Electric A-87
Great job on the cabinet. PS. In the US notation, "kenotron" refers to specific type of tubes; we call re...morzh — 08:24 AM
Part numbers to model cross
This document has at least some tables of models and parts used. Example: Choke 32-7572, used in 604 radio. Search f...morzh — 08:19 AM
Restoration of the Canadian General Electric A-87
I also checked all the radio tubes on my Hickok 530 tube tester. The 5Z3 kenotron turned out to be faulty, all the other...RadioSvit — 08:02 AM
Restoration of the Canadian General Electric A-87
Well... While the varnish is drying up, I started repairing the chassis... Of course I started by replacing the pa...RadioSvit — 07:12 AM
Philco Model 38-7: what caps & resistors do fail typically?
Hello Martin, Welcome aboard our little community what great Model 38-7 Sincerely Richardradiorich — 12:30 AM
Philco Model 38-7: what caps & resistors do fail typically?
Welcome to the Phorum Martin. I count about 9 paper caps, the 3 electrolytic caps and 2-Y2 safety caps to replace th...RodB — 09:44 PM

[-]
Who's Online
There are currently no members online.

>