General Television Inc Radio

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

General Television Inc Radio

Radioroslyn
Phorum Expert

Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa

03-27-2011, 09:21 AM

Found another variant on epay.
http://cgi.ebay.com/Super-Simplex-Wood-M...2556ecc72f

Same diagram on the bottom.
Terry

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

General Television Inc Radio - by 7estatdef - 03-25-2011, 07:07 PM

Re: General Television Inc Radio - by Ron Ramirez - 03-25-2011, 08:48 PM

Re: General Television Inc Radio - by 7estatdef - 03-25-2011, 10:28 PM

Re: General Television Inc Radio - by Jayce - 03-26-2011, 06:36 PM

Re: General Television Inc Radio - by 7estatdef - 03-26-2011, 07:11 PM

Re: General Television Inc Radio - by TA Forbes - 03-26-2011, 09:20 PM

Re: General Television Inc Radio - by 7estatdef - 03-26-2011, 10:49 PM

Re: General Television Inc Radio - by TA Forbes - 03-27-2011, 12:23 AM

Re: General Television Inc Radio - by 7estatdef - 03-27-2011, 09:21 AM

Re: General Television Inc Radio - by 7estatdef - 05-02-2011, 07:16 PM

Re: General Television Inc Radio - by 7estatdef - 05-02-2011, 09:51 PM

Re: General Television Inc Radio - by Jayce - 05-03-2011, 12:49 PM

Re: General Television Inc Radio - by Arran - 05-05-2011, 01:23 AM

Re: General Television Inc Radio - by 7estatdef - 05-05-2011, 05:15 PM

Re: General Television Inc Radio - by Arran - 05-06-2011, 12:57 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 718 online users. [Complete List]
» 1 Member(s) | 717 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me