Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 40-180 Cabinet Restoration
#4

Good Sunday Morning All!

Couple of questions when it comes to getting the supplies I need. I've already got the veneer for my patching job, but looking for some recommendations on the other stuff:

1. Who is your preferred supplier/suppliers or store for the Mohawk toners, laquers, etc?
2. Who is your preferred supplier/suppliers or store for Timbermate wood filler?

I like to shop local when I can, but not aware of any stores around here that carry this stuff (I know my local hardware store does not). Just curious who you guys like to use for your supplies.

Also, how much toner and clear lacquer should I plan to buy for this restoration? I wasn't sure how many cans I need for the typical floor cabinet.

Hoping for a stretch 65+ degree dry weather soon so that I can get this project on a roll. However, I do live in southeast Indiana, so April can bring anything from tornadoes to snow, but I am hopeful!

Vinny
Greensburg, IN

"We don't care what you do...just don't electrocute yourself or burn the house down."
-My Parents


Messages In This Thread
RE: Philco 40-180 Cabinet Restoration - by unclevinny86 - 03-28-2021, 11:36 AM
RE: Philco 40-180 Cabinet Restoration - by DuMont - 06-26-2021, 06:20 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 finished!!
Actually the Loctal tube series, with number beginning with "14" are 12.6 volt tubes, at 150 ma, I'm not sure ...Arran — 02:14 AM
philco predicta
The model is the holiday without UHF It has no sound and I don't have an oscilloscope or signal generator.cgl18 — 08:51 PM
Philco model 38 code 121 not receiving signal.
I will definitely check my lead length and wire dressing. Thanks for the ideas.Stormlord5500 — 08:06 PM
Philco model 38 code 121 not receiving signal.
Do make sure that you twist the 3 wires from the chassis to the transformer, and dress away from tubes, especially audio...MrFixr55 — 07:38 PM
Philco model 38 code 121 not receiving signal.
The cone unfortunately got damaged when I removed it. The glue that held the cone to the basket was sloppily applied and...Stormlord5500 — 07:12 PM
Philco model 38 code 121 not receiving signal.
So what was wrong with the original speaker? Was the cone damaged? Unless it's totally hopeless I would put it aside as ...Arran — 05:31 PM
My collection presentation
There is an article on my site that introduces the first portable radios in my collection. I have only provided a link t...Vlad95 — 01:17 PM
Electrolytic restuffing/internals
Bridkarl This specific cap you have is the easiset type to restuff. I usually cut it at the upper border of the depr...morzh — 11:35 AM
philco predicta
Hi CGL18, First off, welcome to the Philco Phorum. I have not worked on a TV for a while but here are some givens: ...MrFixr55 — 08:22 AM
Another amp build - here I go again!
Sweet! I actually have a Dynaco Mark 4 that I had been running with 6L6s with no mods. Seemed to my 14-year-old head a...MrFixr55 — 12:57 AM

[-]
Who's Online
There are currently 1162 online users. [Complete List]
» 3 Member(s) | 1159 Guest(s)
AvatarAvatarAvatar

>