Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

RCA 56X5
#5

Tonight I did a complete alignment on the 56X5. I guess somebody with nothing better to do began to play with visible screws because things were WAY off. First I set the IF, had to reset both adjustments on both IF transformers, A LOT. Went back and forth a few times and got them peaked at 455KC. Then I went on with the rest of the alignment and had MAJOR adjustments at every stage, but finally got it all dialed in. It receives well on both the standard AM broadcast band and shortwave, despite having a marginal 12SQ7 first detector/oscillator tube. I even was able to pick up WWV at 10 MC using just my 10 foot indoor test antenna, not to mention quite a number of other shortwave stations in both the 9 - 10 MC and the 11 - 12 MC international broadcast bands. It will be fun to see how this radio performs once I have it all finished, have installed a new 12SQ7, and test it on my outdoor antenna.


Messages In This Thread
RCA 56X5 - by mikethedruid - 05-19-2021, 10:34 PM
RE: RCA 56X5 - by Paul Philco322 - 05-20-2021, 07:26 AM
RE: RCA 56X5 - by radiorich - 05-20-2021, 09:18 PM
RE: RCA 56X5 - by mikethedruid - 05-20-2021, 09:23 PM
RE: RCA 56X5 - by mikethedruid - 05-20-2021, 11:15 PM
RE: RCA 56X5 - by mikethedruid - 06-01-2021, 04:40 AM
RE: RCA 56X5 - by mikethedruid - 07-19-2021, 10:41 PM
RE: RCA 56X5 - by EdHolland - 07-20-2021, 01:30 PM
RE: RCA 56X5 - by Paul Philco322 - 07-20-2021, 08:43 PM
RE: RCA 56X5 - by mikethedruid - 07-20-2021, 10:01 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>