Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 51 mantel clock & radio
#3

Hi,

They turn up on Ebay from time to time and I've seen them sell there for as much as $500 a couple of years back. I actually have a couple of them, one shown on my website that started off in pretty rough shape & the other in good original condition:-

http://www.tuberadioland.com/philco551_c..._main.html

Ron Ramirez in his book lists it as fairly hard to find. It uses the same chassis as the 51 and 52 cathedrals. About 25,000 of each of these was made, which probably also includes the number of these clocks.

There is also a model 80 colonial clock in a very similar case. It differs only in that it has two knobs rather than three for the 551.

The radio shown by m82alpa (on the radioattic, I believe) has the incorrect finials and clock hands.

Paul


Messages In This Thread
Philco 51 mantel clock & radio - by Guest - 04-04-2006, 10:35 PM
[No subject] - by Chuck Schwark - 04-04-2006, 10:51 PM
[No subject] - by PTurney - 04-04-2006, 11:01 PM
[No subject] - by Chuck Schwark - 04-04-2006, 11:25 PM
[No subject] - by Guest - 04-05-2006, 08:46 AM
[No subject] - by PTurney - 04-05-2006, 03:18 PM
[No subject] - by Guest - 04-05-2006, 04:31 PM
Model 551 Colonial Clock - by Guest - 04-21-2006, 09:30 AM
[No subject] - by PTurney - 04-25-2006, 08:53 AM
[No subject] - by Guest - 04-25-2006, 07:13 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently 723 online users. [Complete List]
» 1 Member(s) | 722 Guest(s)
Avatar

>