Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

HBC Dictator followed me home...
#5

Yes, the escutcheons will need to be addressed...I think I will polish them, then use gun bluing to give them a bronze look again.

The use of the Dictator name by HBC didn't end with the war, as one might have thought, which is odd. They used the name briefly when the 1946-47 models came out, then switched to Baycrest and Messenger branding for radios. Maybe they realized the folly, or had some kind of public backlash? Or was the term "dictator" not as poorly received back then as it is today?

I've worked on a couple 1946 Dictator sets, and they seem to be a mish-mash of 1941 chassis, with newer "war-time" tubes thrown into the mix. And I was unable to find schematics for either of them. So...were there incomplete cabinets, chassis or whole sets sitting in storage? Or did The Bay have Dominion Electrohome make up sets, using leftover parts in storage? 

As a side note...Studebaker used the name Dictator on their upper line of cars, only to quickly drop the name in 1937, after Hitler tainted the word.


Messages In This Thread
HBC Dictator followed me home... - by Brad Winder - 11-10-2021, 12:57 AM
RE: HBC Dictator followed me home... - by Arran - 11-10-2021, 11:19 PM
RE: HBC Dictator followed me home... - by Brad Winder - 11-12-2021, 11:22 AM
RE: HBC Dictator followed me home... - by Arran - 11-23-2021, 08:08 AM



Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 962 online users. [Complete List]
» 2 Member(s) | 960 Guest(s)
AvatarAvatar

>