Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

National NC-60-Special
#11

The 40 MFD filter condensers arrived today, so I have finished all the under chassis work on the National NC-60-Special. I have done a basic alignment, during which time I found the band switch was VERY scratchy, so that got a good cleaning and is now drying before I continue later tonight with final alignment. It is working pretty well on all bands, and I look forward to checking it out on my outside antenna once all the bench work is done. Here is what the under chassis looks like with the filter condensers installed. They are on the right, attached to the long terminal strip, near the speaker.

[Image: https://64.media.tumblr.com/0c3db7e87f2f...63477d.jpg]


Messages In This Thread
National NC-60-Special - by mikethedruid - 11-10-2021, 07:04 PM
RE: National NC-60-Special - by PhilcoMike - 11-11-2021, 05:22 PM
RE: National NC-60-Special - by mikethedruid - 11-11-2021, 07:15 PM
RE: National NC-60-Special - by PhilcoMike - 11-12-2021, 01:08 PM
RE: National NC-60-Special - by tbone - 11-14-2021, 07:26 PM
RE: National NC-60-Special - by mikethedruid - 11-15-2021, 04:22 AM
RE: National NC-60-Special - by Eliot Ness - 11-15-2021, 09:19 AM
462ron - by 462ron - 11-15-2021, 12:37 PM
RE: National NC-60-Special - by Radioroslyn - 11-15-2021, 03:52 PM
RE: National NC-60-Special - by mikethedruid - 11-15-2021, 04:21 PM
RE: National NC-60-Special - by mikethedruid - 11-15-2021, 05:27 PM
RE: National NC-60-Special - by Radioroslyn - 11-15-2021, 08:45 PM
RE: National NC-60-Special - by mikethedruid - 11-15-2021, 10:25 PM
RE: National NC-60-Special - by radiorich - 11-15-2021, 11:30 PM
RE: National NC-60-Special - by mikethedruid - 11-18-2021, 11:03 AM
RE: National NC-60-Special - by EdHolland - 12-01-2021, 10:35 PM
RE: National NC-60-Special - by PhilcoMike - 12-02-2021, 04:14 PM
RE: National NC-60-Special - by mikethedruid - 12-02-2021, 04:49 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>