1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
An Introduction and a Philco 90 issue.
morzh
Odobenus rosmarus
******
Posts: 16,507
Threads: 572
Joined: Oct 2011
City: Jackson State, Province, Country: NJ
#21

11-24-2021, 09:34 PM
cknob

What are you planning to do with 10uF and 20uF 200V caps?

May I suggest something? It seems to me you are just do trial and error and "maybe it will work" approach.
It rarely works.

Maybe it is a good time to stop and try to understand what you are trying to do and why.

Develop a plan. And go by it. The photo of the chassis you put here looks horrible. I sincerely hope this is what you are trying to fix, and not what you think you have fixed.

Find out what parts to use, what not to use, check the wiring. Do not just turn it on: I've been fixing these for over 10 years AND I am an EE, AND I will never ever turn a radio on UNTIL I fully checked everything.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
An Introduction and a Philco 90 issue. - by cknob - 11-23-2021, 09:20 PM
RE: An Introduction and a Philco 90 issue. - by morzh - 11-24-2021, 09:34 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration