Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 2 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Westinghouse N-202
#32

Not quite done with this radio yet.  I've read about folks adding an AUX input jack so you could plug in an MP3 player or a Bluetooth receiver and this radio seemed like a good one to learn on.  I looked at powering a bluetooth board within the chassis but decided on an easier route for my initial go at this.  I bought a cheap bluetooth receiver, some 3.5mm stereo jacks and some small SPDT switches.  The stereo jack went into the hole where the phono jack originally was and the switch into a small hole that was above the phono jack.  The left and right stereo lines are combined with two 1k resistors and a 10k resistor as shown below.  All in all it seemed to work out fine.  AM in our area is terrible and this set will likely be sold locally so folks can hear something beyond talk radio if they so desire. 

I think I could have used a switched jack to eliminate the SPDT switch but when first thinking about this I didn't realize that.
[Image: https://www.dropbox.com/s/7x3z02r9vquvvg....jpg?raw=1]

Under the chassis the stereo jack and switch are in the lower right corner with the shielded line going to the high end of the volume pot.

[Image: https://www.dropbox.com/s/jp81lr78r2hbaw....jpg?raw=1]

[Image: https://www.dropbox.com/s/3sjs7bafdsuuer....jpg?raw=1]


Messages In This Thread
Westinghouse N-202 - by klondike98 - 03-29-2022, 08:11 PM
RE: Westinghouse N-202 - by captainclock1988 - 03-30-2022, 10:37 AM
RE: Westinghouse N-202 - by klondike98 - 03-30-2022, 04:42 PM
RE: Westinghouse N-202 - by GarySP - 03-30-2022, 05:01 PM
RE: Westinghouse N-202 - by klondike98 - 04-03-2022, 10:14 PM
RE: Westinghouse N-202 - by klondike98 - 05-06-2022, 09:54 PM
RE: Westinghouse N-202 - by Mondial - 05-06-2022, 10:31 PM
RE: Westinghouse N-202 - by captainclock1988 - 05-07-2022, 03:01 AM
RE: Westinghouse N-202 - by RodB - 05-07-2022, 08:44 AM
RE: Westinghouse N-202 - by klondike98 - 05-07-2022, 11:57 AM
RE: Westinghouse N-202 - by RodB - 05-07-2022, 01:35 PM
RE: Westinghouse N-202 - by klondike98 - 05-07-2022, 10:11 PM
RE: Westinghouse N-202 - by klondike98 - 05-14-2022, 09:29 PM
RE: Westinghouse N-202 - by RodB - 05-14-2022, 10:28 PM
RE: Westinghouse N-202 - by Chas - 05-15-2022, 10:01 AM
RE: Westinghouse N-202 - by klondike98 - 05-15-2022, 04:36 PM
RE: Westinghouse N-202 - by GarySP - 05-15-2022, 05:45 PM
RE: Westinghouse N-202 - by klondike98 - 05-15-2022, 07:00 PM
RE: Westinghouse N-202 - by Arran - 05-15-2022, 09:29 PM
RE: Westinghouse N-202 - by klondike98 - 05-16-2022, 12:54 PM
RE: Westinghouse N-202 - by klondike98 - 05-23-2022, 07:47 PM
RE: Westinghouse N-202 - by MrFixr55 - 05-23-2022, 09:17 PM
RE: Westinghouse N-202 - by klondike98 - 05-23-2022, 11:06 PM
RE: Westinghouse N-202 - by klondike98 - 05-25-2022, 09:22 PM
RE: Westinghouse N-202 - by GarySP - 05-25-2022, 10:06 PM
RE: Westinghouse N-202 - by radiorich - 05-25-2022, 11:50 PM
RE: Westinghouse N-202 - by klondike98 - 05-30-2022, 10:03 PM
RE: Westinghouse N-202 - by MrFixr55 - 05-31-2022, 07:18 AM
RE: Westinghouse N-202 - by klondike98 - 06-02-2022, 09:47 PM
RE: Westinghouse N-202 - by GarySP - 06-03-2022, 09:13 AM
RE: Westinghouse N-202 - by Paul Philco322 - 06-03-2022, 04:36 PM
RE: Westinghouse N-202 - by klondike98 - 06-13-2022, 10:43 PM
RE: Westinghouse N-202 - by MrFixr55 - 06-13-2022, 11:25 PM
RE: Westinghouse N-202 - by klondike98 - 06-15-2022, 07:03 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 958 online users. [Complete List]
» 1 Member(s) | 957 Guest(s)
Avatar

>