Predicta Lens Polishing

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Predicta Lens Polishing

Radioroslyn
Phorum Expert

Posts: 7,301
Threads: 269
Joined: Dec 2009
City: Roslyn Pa

07-05-2022, 11:24 AM

Hi and welcome,

I have two questions for you. Are you trying to get rid of light scratches? Or are you hoping to lighten the yellow/brown patina it's acquired over the last 60 yrs?

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Predicta Lens Polishing - by 1962300 - 07-02-2022, 08:20 PM

RE: Predicta Lens Polishing - by morzh - 07-02-2022, 08:51 PM

RE: Predicta Lens Polishing - by 1962300 - 07-04-2022, 03:23 PM

RE: Predicta Lens Polishing - by morzh - 07-04-2022, 06:12 PM

RE: Predicta Lens Polishing - by radiorich - 07-04-2022, 09:25 PM

RE: Predicta Lens Polishing - by Radioroslyn - 07-05-2022, 11:24 AM

RE: Predicta Lens Polishing - by Bob Andersen - 10-23-2022, 08:46 AM

RE: Predicta Lens Polishing - by 1962300 - 10-23-2022, 01:46 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2220 online users. [Complete List]
» 2 Member(s) | 2218 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me