Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Zenith 7s488 assistance request
#10

Rob

This is not a higher math.

Take a meter, set it on volts, and strart going along the line of feeding the power to the 6A8 plate. 0V? OK, how about the other side of that same RF transformer primary? Again 0V? Go tro the bus it is connected to. Itr is literally 5 minutes to trace.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Zenith 7s488 assistance request - by Rob Quay - 07-24-2022, 09:14 PM
RE: Zenith 7s488 assistance request - by morzh - 07-25-2022, 08:40 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 07:52 AM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 02:36 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 04:32 PM
RE: Zenith 7s488 assistance request - by MrFixr55 - 07-26-2022, 07:49 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-26-2022, 08:47 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-27-2022, 02:03 PM
RE: Zenith 7s488 assistance request - by morzh - 07-27-2022, 08:33 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-27-2022, 11:46 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-28-2022, 08:51 PM
RE: Zenith 7s488 assistance request - by MrFixr55 - 07-29-2022, 04:59 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-31-2022, 08:42 AM
RE: Zenith 7s488 assistance request - by morzh - 07-31-2022, 11:08 AM
RE: Zenith 7s488 assistance request - by Rob Quay - 07-31-2022, 09:53 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-03-2022, 09:27 AM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-11-2022, 09:21 AM
RE: Zenith 7s488 assistance request - by MrFixr55 - 08-16-2022, 11:42 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-17-2022, 09:33 AM
RE: Zenith 7s488 assistance request - by MrFixr55 - 08-17-2022, 09:14 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-18-2022, 09:12 AM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-20-2022, 10:10 AM
RE: Zenith 7s488 assistance request - by MrFixr55 - 08-21-2022, 10:04 AM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-21-2022, 11:14 AM
RE: Zenith 7s488 assistance request - by MrFixr55 - 08-21-2022, 05:55 PM
RE: Zenith 7s488 assistance request - by Rob Quay - 08-21-2022, 09:29 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>