Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco with Phono input
#3

Hi Thom,

>The radio was in a cream plastic or bakelite case, and had a jack on the side that the phono plugged into. This would have been sometime in the early 50's. I have looked thru the photo files from 1946 on, but have not found anything like it.

Could you post a pic? Is there a family photo around that may show it in the background? Philco or not a lot of us here have seen and or worked on a LOT of different sets. It would be a big help. It's a little odd that it would have the jack on the side. Most manufactures would relegate them to the back of the set. If I had to guess I would say that it was added on at some point and wasn't original.

Sorry to say you are not giving us much to work with. If there was a bit more to work with it would be easier. If you have a lot of time to kill: https://radioatticarchives.com/ There's about 13.5K sets to peruse.

G.L.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry


Messages In This Thread
Philco with Phono input - by Thomas Day - 08-05-2022, 01:50 PM
RE: Philco with Phono input - by GarySP - 08-05-2022, 02:52 PM
RE: Philco with Phono input - by Radioroslyn - 08-06-2022, 09:44 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
philcorepairbench.com - shadow-meter
Anyone know of a way to recover these files from the repair bench? Thanks. fenbach — 11:16 PM
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM

[-]
Who's Online
There are currently 2066 online users. [Complete List]
» 2 Member(s) | 2064 Guest(s)
AvatarAvatar

>