Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

AWA battery eliminator issue
#1

Hi Guys,
I’m in the process of assembling an AWA battery eliminator for an AK 30 and have run into an issue. After putting the B voltage section together there’s a short. When I disconnect either transformer secondary (Triad VPS230-110),the short disappears. The PC has been triple checked for incorrect part placement and solder joints checked for neatness. 
After putting together a half dozen AES eliminators I figured this one would be easy. Not so. I’m looking for advice on tracking down the problem. The printed circuit board gets confusing to my 70 year old eyes! Thoughts?
Thanks! - Rob Q.


Messages In This Thread
AWA battery eliminator issue - by Rob Quay - 01-21-2023, 09:43 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-22-2023, 01:28 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-22-2023, 10:39 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-24-2023, 09:16 PM
RE: AWA battery eliminator issue - by Rob Quay - 01-25-2023, 04:28 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-25-2023, 08:46 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-25-2023, 09:46 PM
RE: AWA battery eliminator issue - by Rob Quay - 01-25-2023, 10:49 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-26-2023, 08:27 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-26-2023, 09:52 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-26-2023, 12:56 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-26-2023, 05:43 PM
RE: AWA battery eliminator issue - by radiorich - 01-27-2023, 02:02 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-27-2023, 03:33 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-27-2023, 10:12 PM
RE: AWA battery eliminator issue - by radiorich - 01-27-2023, 10:22 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2145 online users. [Complete List]
» 1 Member(s) | 2144 Guest(s)
Avatar

>