Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

AWA battery eliminator issue
#10

Thanks for the step by step! I’ll follow through with your suggestions.
The heat sink short got my attention right away. To me it seemed counterintuitive to insulate a component from a heat sink. That wasn’t an issue with the AES battery eliminators I built. 
I was going to buy an Arbeii III for use with the AK 30 but was interested in the AWA  battery eliminator. It would have cost less also. Prices have increased since the PCB was introduced. It also took 7 months to fill the parts order. 
Hopefully our back and forth troubleshooting on the Phorum will be beneficial to anyone struggling with the lack of information out there. I’ll keep you updated!


Messages In This Thread
AWA battery eliminator issue - by Rob Quay - 01-21-2023, 09:43 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-22-2023, 01:28 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-22-2023, 10:39 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-24-2023, 09:16 PM
RE: AWA battery eliminator issue - by Rob Quay - 01-25-2023, 04:28 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-25-2023, 08:46 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-25-2023, 09:46 PM
RE: AWA battery eliminator issue - by Rob Quay - 01-25-2023, 10:49 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-26-2023, 08:27 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-26-2023, 09:52 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-26-2023, 12:56 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-26-2023, 05:43 PM
RE: AWA battery eliminator issue - by radiorich - 01-27-2023, 02:02 AM
RE: AWA battery eliminator issue - by Rob Quay - 01-27-2023, 03:33 PM
RE: AWA battery eliminator issue - by MrFixr55 - 01-27-2023, 10:12 PM
RE: AWA battery eliminator issue - by radiorich - 01-27-2023, 10:22 PM



Users browsing this thread:
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 982 online users. [Complete List]
» 1 Member(s) | 981 Guest(s)
Avatar

>