1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Restoring a Philco 38-1
Guest
Unregistered
 
#5

05-23-2006, 04:40 PM
Hi Pat:

I sent you an email diretly, but thought I'd post it here also, in case you missed it or should anyone else wish to chime in.

I'm a complete neophyte when it comes to the electronics in these things. I'm pretty handy with a soldering iron, though, so I'm sure I can handle the project if I know what I'm doing.

What exactly are the electrolytic caps and how do I go about getting replacements and changing them? The chassis doesn't look that complicated, but is there some direction you can steer me in as far as someone with no previous experience doing this himself?

Thanks.
« Next Oldest | Next Newest »
Thread Closed


Messages In This Thread
Restoring a Philco 38-1 - by Guest - 05-17-2006, 11:03 PM
[No subject] - by planigan - 05-22-2006, 12:09 PM
[No subject] - by planigan - 05-22-2006, 09:56 PM
[No subject] - by planigan - 05-22-2006, 10:30 PM
[No subject] - by Guest - 05-23-2006, 04:40 PM
[No subject] - by Terry Judkins - 05-23-2006, 10:09 PM
[No subject] - by planigan - 05-24-2006, 02:39 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration