Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Model 90 bezel
#10

Good point, Terry. This is especially important since the service information over the decades regarding the "mid" version 90 has a glaring error - in much of the literature, the "mid" 90 is listed with an IF of 260 kc. This is incorrect. The "mid" 90, like the early 90, has an IF of 175 kc. Only the "late" 90 (with two 47 output tubes) has a 260 kc IF.

I just finished a "mid" 90 (I've been writing about it on my blog) and it received proper alignment at 175 kc. It is, by far, the best and most sensitive 90 I have ever owned. (Oh, darn, I just gave away the ending!) Icon_lolno

--
Ron Ramirez
Ferdinand IN


Messages In This Thread
Model 90 bezel - by Radioroslyn - 05-13-2023, 07:45 PM
RE: Model 90 bezel - by Ron Ramirez - 05-13-2023, 09:06 PM
RE: Model 90 bezel - by Brad Winder - 05-14-2023, 11:11 AM
RE: Model 90 bezel - by Ron Ramirez - 05-14-2023, 11:14 AM
RE: Model 90 bezel - by Brad Winder - 05-14-2023, 11:19 AM
RE: Model 90 bezel - by klondike98 - 05-14-2023, 11:49 AM
RE: Model 90 bezel - by Ron Ramirez - 05-14-2023, 12:41 PM
RE: Model 90 bezel - by Ron Ramirez - 05-14-2023, 12:53 PM
RE: Model 90 bezel - by Radioroslyn - 05-14-2023, 01:19 PM
RE: Model 90 bezel - by Ron Ramirez - 05-14-2023, 02:10 PM
RE: Model 90 bezel - by Nathan Slingerland - 05-14-2023, 10:12 PM
RE: Model 90 bezel - by Radioroslyn - 05-15-2023, 09:52 AM
RE: Model 90 bezel - by Ron Ramirez - 05-15-2023, 11:56 AM
RE: Model 90 bezel - by Radioroslyn - 05-16-2023, 10:29 AM
RE: Model 90 bezel - by Ron Ramirez - 05-16-2023, 11:14 AM
RE: Model 90 bezel - by admin - 05-16-2023, 11:16 AM
RE: Model 90 bezel - by Ron Ramirez - 05-16-2023, 01:51 PM
RE: Model 90 bezel - by DaleHCook - 05-16-2023, 06:53 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
Thankyou for the kind words sir. I double checked it with my component tester and it read 2.7 ohms at .02mH.Stormlord5500 — 08:14 AM
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM

[-]
Who's Online
There are currently 728 online users. [Complete List]
» 2 Member(s) | 726 Guest(s)
AvatarAvatar

>