Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-116 Period Correct Wiring
#5

Just no telling what color they will fade to. After all did you think you would have the same color hair you did all that time ago, if you still have some? Me neither. Once again green was the 6.3 winding, yellow was the 5.0 winding, and red was the high voltage winding. Center taps were usually staggared colors, sometimes the 6.3 had a yellow trail, the cener tap of the 5 volt winding may or may not be be present, and could be any color, but the b+ enter tap almost always had a varigated color scheme. You can always take out all the tubes, and fire the set up, and measure what you find. All will be up a little bit, maybe a lot,because there is no load applied.

Put a 1 Ampere fuse ahead of the transformer before doing any measurements. Tell us wyat you have found.


Messages In This Thread
37-116 Period Correct Wiring - by qanerd - 06-21-2011, 04:57 PM
Re: 37-116 Period Correct Wiring - by Arran - 06-21-2011, 09:01 PM
Re: 37-116 Period Correct Wiring - by codefox1 - 06-21-2011, 10:45 PM
Re: 37-116 Period Correct Wiring - by qanerd - 06-21-2011, 11:41 PM
Re: 37-116 Period Correct Wiring - by codefox1 - 06-22-2011, 12:19 AM
Re: 37-116 Period Correct Wiring - by qanerd - 06-22-2011, 12:51 PM
Re: 37-116 Period Correct Wiring - by exray - 06-22-2011, 01:44 PM
Re: 37-116 Period Correct Wiring - by qanerd - 06-22-2011, 03:11 PM
Re: 37-116 Period Correct Wiring - by exray - 06-22-2011, 03:46 PM
Re: 37-116 Period Correct Wiring - by qanerd - 06-22-2011, 04:10 PM
Re: 37-116 Period Correct Wiring - by Arran - 06-22-2011, 05:58 PM
Re: 37-116 Period Correct Wiring - by qanerd - 06-22-2011, 11:44 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2181 online users. [Complete List]
» 2 Member(s) | 2179 Guest(s)
AvatarAvatar

>