Midwest 88

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Midwest 88

bridkarl
Member

Posts: 198
Threads: 44
Joined: May 2023
City: Pocatello State, Province, Country: idaho

09-02-2023, 07:40 PM

I’m near sixty and expect to be dead in five to ten years.
I’m well past worrying about anyone’s opinion.

I got a Facebook account - not looking for positive affirmations - but just to share some of my experience. I thought people would appreciate it. I was wrong. Bad experiment not to be repeated.

I have a tremor from nerve damage. It’s not usually a problem but why I stay well away from any radio after about 1965. Just can’t do circuit boards usually.

People here are agreeable. Have a great holiday everyone.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Midwest 88 - by bridkarl - 09-02-2023, 06:28 PM

RE: Midwest 88 - by morzh - 09-02-2023, 07:21 PM

RE: Midwest 88 - by bridkarl - 09-02-2023, 07:40 PM

RE: Midwest 88 - by morzh - 09-02-2023, 09:26 PM

RE: Midwest 88 - by MrFixr55 - 09-03-2023, 09:22 PM

RE: Midwest 88 - by bridkarl - 09-04-2023, 09:48 AM

RE: Midwest 88 - by Paul Philco322 - 09-04-2023, 11:10 AM

RE: Midwest 88 - by Chas - 09-04-2023, 12:17 PM

RE: Midwest 88 - by GarySP - 09-04-2023, 12:17 PM

RE: Midwest 88 - by Ron Ramirez - 09-04-2023, 12:26 PM

RE: Midwest 88 - by morzh - 09-04-2023, 02:30 PM

RE: Midwest 88 - by Arran - 09-04-2023, 03:16 PM

RE: Midwest 88 - by morzh - 09-04-2023, 06:12 PM

RE: Midwest 88 - by RodB - 09-05-2023, 09:19 AM

RE: Midwest 88 - by morzh - 09-05-2023, 10:57 AM

RE: Midwest 88 - by bridkarl - 09-05-2023, 07:19 PM

RE: Midwest 88 - by morzh - 09-05-2023, 08:15 PM

RE: Midwest 88 - by bridkarl - 09-05-2023, 08:50 PM

RE: Midwest 88 - by morzh - 09-06-2023, 04:23 PM

RE: Midwest 88 - by GarySP - 09-07-2023, 10:00 AM

RE: Midwest 88 - by morzh - 09-07-2023, 02:05 PM

RE: Midwest 88 - by Joe Rossi - 09-07-2023, 03:38 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online

There are currently 953 online users. [Complete List]
» 2 Member(s) | 951 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me