Resistors used in Model 20

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Resistors used in Model 20

Ron Ramirez
Silent Key

Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana

#12

09-28-2023, 02:42 PM

Yeah, I started buying 1W resistors exclusively a couple years ago as I replenish my resistor stock. They are still much smaller than the original dogbones. For that matter, some modern 1W resistors are even smaller than older 1/2W carbon composition resistors.

> Findatube lists new 71A at $21.00

That reminds me... I need to order a few tubes from Bob D. ...not 71As, though.

--
Ron Ramirez
Ferdinand IN

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Resistors used in Model 20 - by MrFixr55 - 09-26-2023, 10:18 PM

RE: Resistors used in Model 20 - by morzh - 09-26-2023, 11:59 PM

RE: Resistors used in Model 20 - by radiorich - 09-27-2023, 08:06 AM

RE: Resistors used in Model 20 - by MrFixr55 - 09-27-2023, 10:10 AM

RE: Resistors used in Model 20 - by morzh - 09-27-2023, 10:36 AM

RE: Resistors used in Model 20 - by Arran - 09-27-2023, 06:11 PM

RE: Resistors used in Model 20 - by morzh - 09-27-2023, 06:54 PM

RE: Resistors used in Model 20 - by Ron Ramirez - 09-27-2023, 07:20 PM

RE: Resistors used in Model 20 - by radiorich - 09-28-2023, 08:36 AM

RE: Resistors used in Model 20 - by morzh - 09-28-2023, 09:02 AM

RE: Resistors used in Model 20 - by GarySP - 09-28-2023, 02:19 PM

RE: Resistors used in Model 20 - by Ron Ramirez - 09-28-2023, 02:42 PM

RE: Resistors used in Model 20 - by morzh - 09-28-2023, 03:18 PM

RE: Resistors used in Model 20 - by MrFixr55 - 09-28-2023, 05:37 PM

RE: Resistors used in Model 20 - by morzh - 09-28-2023, 08:25 PM

RE: Resistors used in Model 20 - by MrFixr55 - 10-01-2023, 08:59 AM

RE: Resistors used in Model 20 - by Arran - 10-01-2023, 04:37 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online

There are currently 723 online users. [Complete List]
» 1 Member(s) | 722 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me