Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 60 code 121 IF's
#2

Is it possible that the 1st IF currently installed is not designed for 460KHz?  Is the existing 1st IF xformer trimmer tuned, slug tuned or neither?  Maybe hook up the sig generator to the convertor tube and adjust the freq of the sig gen till you peak an output on the secondary of the 1st IF xformer.  Maybe lead dress may be an issue.  ensure thet the wire to the grid cap for the IF tube is not running too close to then IF can or tube shield (if used. )Also, how good is the IF tube.  If the sig gen is not attenuated, you could be blasting through a bad tube.  Also check the wiring and parts in the AVC circuit. an open may cause grid rectification and low gain.

Good luck

"Do Justly, love Mercy and walk humbly with your God"- Micah 6:8
"Let us begin to do good"- St. Francis

Best Regards, 

MrFixr55


Messages In This Thread
Philco 60 code 121 IF's - by Jimradio - 03-14-2024, 07:43 PM
RE: Philco 60 code 121 IF's - by MrFixr55 - 03-15-2024, 10:16 AM
RE: Philco 60 code 121 IF's - by Jimradio - 03-15-2024, 02:19 PM
RE: Philco 60 code 121 IF's - by Jimradio - 03-19-2024, 07:43 AM
RE: Philco 60 code 121 IF's - by RodB - 03-19-2024, 10:19 AM
RE: Philco 60 code 121 IF's - by Jimradio - 03-19-2024, 01:56 PM
RE: Philco 60 code 121 IF's - by Jimradio - 03-19-2024, 03:32 PM
RE: Philco 60 code 121 IF's - by Radioroslyn - 03-19-2024, 05:29 PM
RE: Philco 60 code 121 IF's - by Jimradio - 03-19-2024, 07:27 PM
RE: Philco 60 code 121 IF's - by Radioroslyn - 03-20-2024, 06:27 AM
RE: Philco 60 code 121 IF's - by Jimradio - 03-20-2024, 09:58 AM
RE: Philco 60 code 121 IF's - by radiorich - 03-21-2024, 09:09 AM
RE: Philco 60 code 121 IF's - by Jimradio - 03-21-2024, 11:46 AM
RE: Philco 60 code 121 IF's - by klondike98 - 03-21-2024, 12:04 PM
RE: Philco 60 code 121 IF's - by Radioroslyn - 03-21-2024, 08:51 PM
RE: Philco 60 code 121 IF's - by Jimradio - 03-22-2024, 07:57 AM
RE: Philco 60 code 121 IF's - by radiorich - 03-22-2024, 08:17 AM
RE: Philco 60 code 121 IF's - by Jimradio - 03-22-2024, 11:19 AM
RE: Philco 60 code 121 IF's - by Radioroslyn - 03-22-2024, 12:55 PM
RE: Philco 60 code 121 IF's - by Jimradio - 03-29-2024, 07:48 AM
RE: Philco 60 code 121 IF's - by RodB - 03-29-2024, 10:36 AM
RE: Philco 60 code 121 IF's - by Jimradio - 03-29-2024, 03:09 PM
RE: Philco 60 code 121 IF's - by Jimradio - 03-30-2024, 03:54 PM
RE: Philco 60 code 121 IF's - by Jimradio - 04-04-2024, 09:47 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>