Signal Generator Help Needed

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Signal Generator Help Needed

SRv2
Junior Member

Posts: 27
Threads: 5
Joined: Mar 2024
City: BERTHOUD State, Province, Country: CO

03-26-2024, 09:02 PM

I am using a 0.22uf cap, but I can change that to your suggestion, thanks. Any tips for how you connect that to your signal generator? Are you using some jumper cables, or do you literally touch one end of the cap to the grid or injection point, with the other lead on your positive probe?

George - Berthoud, Colorado. Learned tube receiver repair and troubleshooting in the Navy way back when, came back around to it as an old guy. Re-learning all I can. Doing my part to restore a few of these old gems.

Find

« Next Oldest | Next Newest »

Thread Closed

Messages In This Thread

Signal Generator Help Needed - by SRv2 - 03-24-2024, 05:23 PM

RE: Signal Generator Help Needed - by DaleHCook - 03-25-2024, 05:32 AM

RE: Signal Generator Help Needed - by SRv2 - 03-25-2024, 07:40 AM

RE: Signal Generator Help Needed - by DaleHCook - 03-25-2024, 08:02 AM

462ron - by 462ron - 03-25-2024, 08:04 AM

RE: Signal Generator Help Needed - by SRv2 - 03-25-2024, 08:17 AM

RE: Signal Generator Help Needed - by morzh - 03-26-2024, 08:07 PM

RE: Signal Generator Help Needed - by SRv2 - 03-26-2024, 09:02 PM

RE: Signal Generator Help Needed - by morzh - 03-27-2024, 07:41 PM

RE: Signal Generator Help Needed - by SRv2 - 03-27-2024, 09:01 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2096 online users. [Complete List]
» 1 Member(s) | 2095 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me