Test bench almost done...

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Test bench almost done...

KI5OMM
Junior Member

Posts: 27
Threads: 2
Joined: Oct 2023
City: Huntsville State, Province, Country: TX

04-11-2024, 07:36 PM

That's a lot of hard work, planning, and great ideas that I see everywhere! What type of antenna do you have that you use with that built-in antenna jack?

I want to do something very similar, but my interests have been moving towards restoring "boat anchor" communication equipment. Therefore I want to tailor my needs towards that, by tapping into some of my ham radio antennas outside. Your variac and isolated plugs and gauges is very clean and well planned.

Thanks for sharing and giving me some ideas! Congratulations and I know you'll get some good use out of that!
Bud - KI5OMM

Find

« Next Oldest | Next Newest »

Messages In This Thread

Test bench almost done... - by Brad Winder - 04-08-2024, 12:17 AM

RE: Test bench almost done... - by radiorich - 04-08-2024, 12:35 AM

RE: Test bench almost done... - by RadioSvit - 04-08-2024, 11:28 AM

RE: Test bench almost done... - by morzh - 04-08-2024, 01:41 PM

RE: Test bench almost done... - by slford310 - 04-08-2024, 02:23 PM

RE: Test bench almost done... - by Brad Winder - 04-09-2024, 10:18 AM

RE: Test bench almost done... - by RadioSvit - 04-10-2024, 05:35 AM

RE: Test bench almost done... - by KI5OMM - 04-11-2024, 07:36 PM

RE: Test bench almost done... - by morzh - 04-11-2024, 08:19 PM

RE: Test bench almost done... - by KI5OMM - 04-11-2024, 09:56 PM

RE: Test bench almost done... - by Brad Winder - 04-11-2024, 11:18 PM

RE: Test bench almost done... - by MrFixr55 - 04-13-2024, 09:28 AM

RE: Test bench almost done... - by morzh - 04-13-2024, 01:51 PM

RE: Test bench almost done... - by TV MAN - 09-23-2024, 12:39 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

Who's Online

There are currently 2212 online users. [Complete List]
» 2 Member(s) | 2210 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me