Precision E-200-C

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Precision E-200-C

JLuke
Junior Member

Posts: 11
Threads: 6
Joined: Feb 2021
City: Huntley State, Province, Country: IL

#25

07-27-2024, 12:33 PM

Hi All,

I have an E-200-C Signal Generator. The V10 and V11 assemblies are broken. Any ideas on replacement assemblies? There are 2 variable resistors mounted on each other with the shaft turning both pots.

Regards

Jim Vinton
jamesvinton@comcast.net

Find

« Next Oldest | Next Newest »

Messages In This Thread

Precision E-200-C - by Mike L - 09-17-2016, 07:48 PM

RE: Precision E-200-C - by KCMike - 09-17-2016, 09:50 PM

RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 11:33 PM

RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 01:34 AM

RE: Precision E-200-C - by Mike L - 11-21-2016, 08:49 PM

RE: Precision E-200-C - by KCMike - 11-21-2016, 11:44 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 12:35 AM

RE: Precision E-200-C - by morzh - 11-22-2016, 12:00 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 02:21 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 02:26 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 04:00 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 04:10 PM

RE: Precision E-200-C - by Mondial - 11-23-2016, 10:22 PM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 09:10 AM

RE: Precision E-200-C - by Mondial - 11-24-2016, 10:34 AM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 12:36 PM

RE: Precision E-200-C - by Mike L - 11-26-2016, 05:32 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 03:40 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 04:41 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 05:49 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 07:06 PM

RE: Precision E-200-C - by Mike L - 12-31-2016, 09:33 AM

RE: Precision E-200-C - by Radioroslyn - 01-01-2017, 12:55 AM

RE: Precision E-200-C - by Mike L - 01-01-2017, 05:27 PM

RE: Precision E-200-C - by JLuke - 07-27-2024, 12:33 PM

RE: Precision E-200-C - by DaleHCook - 07-28-2024, 11:29 AM

RE: Precision E-200-C - by RodB - 07-28-2024, 04:59 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM
Philco model 38 code 121 not receiving signal.
Good news everyone! I think I have found everything I need for rewinding the antenna coil primary. I found some pla...Stormlord5500 — 09:40 AM
Philco Battery-WWII vintage
My younger sister went to SUNY Plattsburg NY, (BS, MS, RN) in the late 1970sabout 10 min from the Northern NY / Canada b...MrFixr55 — 07:59 AM

Who's Online

There are currently 1774 online users. [Complete List]
» 3 Member(s) | 1771 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me