Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Help understanding a 89 radio rebuild new guy
#23

Chas,
I meant ferrous.  I'm old, blind, and I use the drop-down spell assistant too much without looking.  I see you are a ham and know that a ferrous antenna is directional.  I however had no luck at RDF tracking.  This noise is everywhere and I have to be somewhat close to some hardware for my radio/RDF tracker to detect it.  I can hear the buzz standing under the power lines but 15 off to the side it's gone.  At every power pole however the radio screams loud.  I'm betting on a lightning arrester but where?  I hope DS&O has some of the equipment you were speaking of.  We will see tomorrow.  BTW in 1967 I became WA0UKB  67 to 77 2 tickets then quit. Don't know why.  Now I have a thirst to play with an old superhet like I used dig out of the trash back in the 60s
88s and I'll be back.
Bruce B


Messages In This Thread
462ron - by 462ron - 09-01-2024, 08:49 AM
462ron - by 462ron - 09-02-2024, 08:04 AM
RE: Help understanding a 89 radio rebuild new guy - by Bruce B - 09-03-2024, 10:11 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently 997 online users. [Complete List]
» 1 Member(s) | 996 Guest(s)
Avatar

>