Philco Model 71B

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco Model 71B

Arran
Phorum Expert

Posts: 4,894
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA

09-10-2024, 12:48 AM

A patriotic mess? I wonder if that was done during the Bicentenary? In my opinion it looks worse then it probably is, such as the arch will likely need to be replaced, but the front doesn't look too bad. A model 71 is pretty much a model 70 but with 6.3 volt tubes, unfortunately I think it also used an autodyne oscillator, which may or may not work correctly once restored.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco Model 71B - by slford310 - 09-09-2024, 09:26 PM

RE: Philco Model 71B - by morzh - 09-09-2024, 09:39 PM

RE: Philco Model 71B - by MrFixr55 - 09-09-2024, 10:02 PM

RE: Philco Model 71B - by slford310 - 09-09-2024, 10:09 PM

RE: Philco Model 71B - by morzh - 09-09-2024, 10:21 PM

RE: Philco Model 71B - by Arran - 09-10-2024, 12:48 AM

RE: Philco Model 71B - by Radioroslyn - 09-10-2024, 11:02 AM

RE: Philco Model 71B - by MrFixr55 - 09-10-2024, 11:21 AM

RE: Philco Model 71B - by GarySP - 09-10-2024, 11:31 AM

RE: Philco Model 71B - by slford310 - 09-13-2024, 10:32 AM

RE: Philco Model 71B - by RodB - 09-13-2024, 05:31 PM

RE: Philco Model 71B - by slford310 - 09-13-2024, 05:38 PM

RE: Philco Model 71B - by MrFixr55 - 09-13-2024, 08:31 PM

RE: Philco Model 71B - by slford310 - 09-13-2024, 09:17 PM

RE: Philco Model 71B - by slford310 - 09-16-2024, 12:46 AM

RE: Philco Model 71B - by Arran - 09-16-2024, 03:59 PM

RE: Philco Model 71B - by slford310 - 09-16-2024, 04:05 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me