Clear Schematic for 41-255

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Clear Schematic for 41-255

RossH
Junior Member

Posts: 17
Threads: 2
Joined: Dec 2020
City: Muhlenberg County State, Province, Country: KY

#18

09-17-2024, 06:19 PM

What's really funny is I looked at the pages and saw 255 and it took me 30 sec of looking at the schematic trying to figure out why it wasn't matching what I had before it dawned on me - I had transposed the numbers in my head.

This is perfect. Besides starting to work on one of these I am going to recreate this schematic from scratch. I've done a few ten others but this will be my first Philco recreation. I'll post when it's completed and gone over a few times.

Thank you very much for your time and consideration in doing this, and a big thank you to all who chimed in.

When you unsolder what has been soldered before the unsoldering, the unsoldering of the soldered is what will be.

(This post was last modified: 09-17-2024, 06:20 PM by RossH.)

Find

« Next Oldest | Next Newest »

Messages In This Thread

Clear Schematic for 41-255 - by RossH - 09-13-2024, 04:27 PM

RE: Clear Schematic for 41-255 - by GarySP - 09-13-2024, 08:59 PM

RE: Clear Schematic for 41-255 - by RossH - 09-13-2024, 09:48 PM

RE: Clear Schematic for 41-255 - by RodB - 09-13-2024, 10:03 PM

RE: Clear Schematic for 41-255 - by klondike98 - 09-13-2024, 10:06 PM

RE: Clear Schematic for 41-255 - by RossH - 09-13-2024, 11:37 PM

RE: Clear Schematic for 41-255 - by Chas - 09-14-2024, 11:02 AM

RE: Clear Schematic for 41-255 - by RossH - 09-14-2024, 11:19 AM

RE: Clear Schematic for 41-255 - by radiorich - 09-14-2024, 11:30 AM

RE: Clear Schematic for 41-255 - by DaleHCook - 09-14-2024, 12:57 PM

RE: Clear Schematic for 41-255 - by RossH - 09-14-2024, 01:38 PM

RE: Clear Schematic for 41-255 - by klondike98 - 09-17-2024, 11:50 AM

RE: Clear Schematic for 41-255 - by RossH - 09-17-2024, 12:32 PM

RE: Clear Schematic for 41-255 - by morzh - 09-17-2024, 01:00 PM

RE: Clear Schematic for 41-255 - by rfeenstra - 09-17-2024, 01:10 PM

RE: Clear Schematic for 41-255 - by DaleHCook - 09-17-2024, 05:12 PM

RE: Clear Schematic for 41-255 - by klondike98 - 09-17-2024, 05:40 PM

RE: Clear Schematic for 41-255 - by RossH - 09-17-2024, 06:19 PM

RE: Clear Schematic for 41-255 - by radiorich - 09-17-2024, 10:35 PM

RE: Clear Schematic for 41-255 - by patrician56 - 09-27-2024, 04:45 PM

RE: Clear Schematic for 41-255 - by patrician56 - 09-27-2024, 05:10 PM

RE: Clear Schematic for 41-255 - by RossH - 09-29-2024, 09:54 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

Who's Online

There are currently 996 online users. [Complete List]
» 1 Member(s) | 995 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me