Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Mission Bell Model 19A Car Radio
#9

Hello everyone, 
As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded to work to make this set "self sufficient". 
We have had some luck here. Initially while the vibrator vibrated , it  seemed  no a.c. was appearing on the rectifier anodes. Checking the  buffer cap across these anodes  showed it to be  very leaky. Replaced with a new 1000 volt  one a healthy a.c. appeared  when the set was powered up  and  with  rectifier plugged in  I measured slightly over 200 volts  between the cathode of the 84 and earth. 
The set is remarkably sensitive especially considering there is no r.f. amplifier.
I have mentioned that there are some differences between the schematic on radiomuseum and this set.The radiomuseum circuit shows a half wave rectifier only. This lends weight to the idea that my set is a later " factory improved " set.

Especial thanks to all who have contributed so helpfully  to identifying and tracking down the make and origins of this set. I'm hoping it will provide an interesting talking point at our next vintage radio club meeting.


Messages In This Thread
Mission Bell Model 19A Car Radio - by Antipodal - 11-07-2024, 08:25 PM
RE: Gilfillan Brothers Car Radio? - by Arran - 11-08-2024, 05:54 AM
RE: Gilfillan Brothers Car Radio? - by Arran - 11-16-2024, 01:24 AM
RE: Gilfillan Brothers Car Radio? - by Antipodal - 11-16-2024, 02:42 AM
RE: Gilfillan Brothers Car Radio? - by Arran - 11-16-2024, 04:12 PM
RE: Gilfillan Brothers Car Radio? - by MrFixr55 - 11-17-2024, 12:22 AM
RE: Gilfillan Brothers Car Radio? - by Joe Rossi - 11-21-2024, 05:01 PM
RE: Gilfillan Brothers Car Radio? - by Antipodal - 11-25-2024, 08:15 PM
RE: Mission Bell Model 19A Car Radio - by Antipodal - 11-26-2024, 08:21 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
5U4 vs 5Z4 tubes
Well this is a Hallicrafters SX/9 circa 1936. No real issues so far although I dodged a real bullet with a cap that was...bridkarl — 07:59 AM
5U4 vs 5Z4 tubes
The pinout is the same but the 5U4 has a 3 amp filament, verses 2 amps or less on the 5Z4. I think that the pinout of a ...Arran — 12:04 AM
Philco 42-345 Restoration/Repair
By the way. osanders0311 Take a look here: Dial cord stringing Guides May be here you can fount correct string settin...Vlad95 — 11:15 PM
5U4 vs 5Z4 tubes
5U4 and 5Z4 almost identical. I think nothing happened if you left 5U4 instedad 5Z4 long time. Just heater current 5U4 ...Vlad95 — 11:02 PM
Philco 42-345 Restoration/Repair
Hello Vlad95 , Very Funny ! Sincerely Richardradiorich — 11:01 PM
Philco 42-345 Restoration/Repair
RodB You are European yourself   :evil: I'm Canadian for the last 30 years  :snowman: But not Yankee  :lol: Vlad95 — 10:49 PM
Philco 42-345 Restoration/Repair
The band switch selects different oscillator coils for the band selected. I would look for a bad connection in the switc...RodB — 10:31 PM
Philco 42-345 Restoration/Repair
Hang in there...PaulPaul Philco322 — 09:30 PM
Philco 42-345 Restoration/Repair
The thrill is gone again, thought I was close to being done with it. Well Friday it was receiving broadcast, Saturday mo...osanders0311 — 07:47 PM
Help with Supreme 599
Iam getting closer to fixing it. I bumped Up the tranny voltage to get 5v on the 80 tube. I gan get the needle to move ...daveone23 — 03:41 PM

[-]
Who's Online
There are currently no members online.

>