Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Thread Closed

Atwater-Kent 84, restoration.
#1

This AK84 was bought, I think, last fall.
For a whopping $100.
It has been, according to the seller, restored.

As I go through radios no matter what the seller tells me, and due to the other project (H-speaker coil restoration) going on the back burner, I decided it is time for that patient to be seen.


This is the radio. The condition is rather nice.

   
   
   
   
   

The chassis is clean, as often is the case with AK.

   
   
   
   

The under-chassis is nice too. Clearly some work has been done.
Also the cord is new.

   

The tubes are good except one 24A tube. It takes a couple of minutes or more to start moving the indicator needle on my 600A Hickok, and slowly, over 2-3 minutes, it gets to 500. Others within a minute of warm-up get above 1000. This gets changed.

The electrolytic caps have been restuffed, which is obvious.

The capacitor can assemblies have been touched, but I am not sure if they were rebuilt. The fact they were touched is betrayed by nice brass screws holding them  instead of the rivets.
But the bottom looks nice and so I am not sure if it has new caps inside.

   

I will unsolder the wires and check the values.

The tuning is a bit tight and rough; the roller that moves the sprocket of the tuner received some plastic piece over it, and this is perhaps why it is.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Atwater-Kent 84, restoration. - by morzh - 02-22-2025, 05:48 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-22-2025, 09:41 PM
RE: Atwater-Kent 84, restoration. - by radiorich - 02-22-2025, 11:21 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-22-2025, 11:31 PM
RE: Atwater-Kent 84, restoration. - by GarySP - 02-23-2025, 12:12 AM
RE: Atwater-Kent 84, restoration. - by radiorich - 02-23-2025, 02:59 AM
462ron - by 462ron - 02-23-2025, 10:22 AM
RE: Atwater-Kent 84, restoration. - by jrblasde - 02-23-2025, 10:50 AM
RE: Atwater-Kent 84, restoration. - by morzh - 02-23-2025, 11:12 AM
RE: Atwater-Kent 84, restoration. - by radiorich - 02-23-2025, 11:25 AM
RE: Atwater-Kent 84, restoration. - by morzh - 02-23-2025, 06:02 PM
462ron - by 462ron - 02-24-2025, 09:10 AM
RE: Atwater-Kent 84, restoration. - by morzh - 02-24-2025, 12:16 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-24-2025, 12:29 PM
462ron - by 462ron - 02-24-2025, 04:14 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-24-2025, 04:51 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-24-2025, 10:21 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-25-2025, 08:24 PM
RE: Atwater-Kent 84, restoration. - by radiorich - 02-25-2025, 09:15 PM
RE: Atwater-Kent 84, restoration. - by Arran - 02-26-2025, 02:29 AM
RE: Atwater-Kent 84, restoration. - by morzh - 02-26-2025, 09:11 AM
RE: Atwater-Kent 84, restoration. - by morzh - 02-27-2025, 08:56 PM
RE: Atwater-Kent 84, restoration. - by radiorich - 02-27-2025, 09:38 PM
RE: Atwater-Kent 84, restoration. - by morzh - 02-27-2025, 09:44 PM
RE: Atwater-Kent 84, restoration. - by radiorich - 02-28-2025, 12:18 AM
462ron - by 462ron - 02-28-2025, 08:44 AM
RE: Atwater-Kent 84, restoration. - by morzh - 03-01-2025, 08:48 PM
RE: Atwater-Kent 84, restoration. - by morzh - 03-02-2025, 02:42 PM
RE: Atwater-Kent 84, restoration. - by morzh - 03-03-2025, 09:33 PM
RE: Atwater-Kent 84, restoration. - by morzh - 03-04-2025, 07:48 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
hello david, I have a similar generator in my collection that features a cast iron, single-cylinder Briggs & Stratt...radiorich — 01:00 AM
under chassis parts locator diagram for 1938 Zenith 9s262
Has anyone gone to the trouble of creating an under chassis parts locator image?  Yes, I can identify components by foll...bobloney — 08:57 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Try looking at this site the book mark is for a old generator that I was given. David    https://radionerds.com/index.ph...David — 08:36 PM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
Hello Everyone, I am looking for voltage identification for all the pin positions on the socket of a CRV-20130 power su...Tonym4704 — 08:16 PM
Philco P45-6365 Universal Transformer Instruction Manual
Can anyone guide me to where this may be found?GRG — 03:00 PM
54C Complete Teardown/Rebuild
I don't think that I have encountered a 12Z3 before, curious how it uses one of those but includes a #43, which is a 25 ...Arran — 02:17 PM
HiFi (Chifi) tube amp build - but my own design.
It's the other forum. I'm also in DIY, but mostly read there. Honestly, I kinda jumped into this without much thought to...TV MAN — 10:43 AM
Philco 71 Code 125
Hello,  I am in need of a schematic for this radio. Mine has the three separate circular tube shields and a shadow me...dconant — 08:06 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated.dconant — 07:57 AM
54C Complete Teardown/Rebuild
Hello Roy, here is this one sincerely Richardradiorich — 12:45 AM

[-]
Who's Online
There are currently no members online.

>