Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 39-7C Restore
#11

Bob

Transformer may heat up for reasons that are not its own; it could be loaded heavier than appropriate.
But if it did not sustain damage, it could be OK.
To me a good way of testing it is plugging it in 120V and running it with no load. If it does not heat up (could get a tad warm) considerably, it is OK (no turn short).
Ohming out is the first check, of course, but it will not reveal a turn short.
This test will.
(BTW this is one instance where I approve using a dim bulb tester).

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.


Messages In This Thread
Philco 39-7C Restore - by klondike98 - 04-15-2024, 08:30 PM
RE: Philco 39-7C Restore - by Paul Philco322 - 04-15-2024, 08:32 PM
RE: Philco 39-7C Restore - by morzh - 04-15-2024, 09:27 PM
RE: Philco 39-7C Restore - by klondike98 - 04-16-2024, 03:04 AM
RE: Philco 39-7C Restore - by morzh - 04-16-2024, 09:48 PM
RE: Philco 39-7C Restore - by klondike98 - 04-16-2024, 11:02 PM
RE: Philco 39-7C Restore - by klondike98 - 04-17-2024, 01:53 PM
RE: Philco 39-7C Restore - by klondike98 - 03-21-2025, 12:41 PM
RE: Philco 39-7C Restore - by morzh - 03-21-2025, 02:05 PM
RE: Philco 39-7C Restore - by klondike98 - 03-21-2025, 03:12 PM
RE: Philco 39-7C Restore - by morzh - 03-21-2025, 04:27 PM
RE: Philco 39-7C Restore - by klondike98 - 03-21-2025, 07:36 PM
RE: Philco 39-7C Restore - by radiorich - 03-21-2025, 09:32 PM
RE: Philco 39-7C Restore - by klondike98 - 03-29-2025, 08:12 PM
RE: Philco 39-7C Restore - by morzh - 03-29-2025, 11:47 PM
RE: Philco 39-7C Restore - by klondike98 - 04-26-2025, 12:06 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM
Philco model 38 code 121 not receiving signal.
Good luck next thing you know you will be winding coils just for the fun of it. DavidDavid — 11:29 AM
Testing a speaker and output transformer Trutone A2-G
morzh Short-circuited turns can be considered as a half-dead transformer. But on this case transformer will hot and s...Vlad95 — 11:01 AM
Testing a speaker and output transformer Trutone A2-G
I am not sure how a transformer could be weak. It could be inadequate, but only when you replace the original with somet...morzh — 09:56 AM

[-]
Who's Online
There are currently 2152 online users. [Complete List]
» 1 Member(s) | 2151 Guest(s)
Avatar

>