Replacing electrolytic cans with E-caps for 40-180?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Replacing electrolytic cans with E-caps for 40-180?

jslim22
Junior Member

Posts: 15
Threads: 6
Joined: Jun 2006

#13

07-27-2006, 10:02 AM

I can actually epoxy the top onto the can itself. There is plenty of surface area.
There is a metallic mesh inside the can. Can I solder the ground lead to this? The can will be ground to the chassis by the bottom threads as before.

Thanks Jun

Find

« Next Oldest | Next Newest »

Messages In This Thread

Replacing electrolytic cans with E-caps for 40-180? - by jslim22 - 07-12-2006, 12:27 AM

Replacing electrolytic cans with e-caps 40-180 - by planigan - 07-12-2006, 02:13 AM

Thanks - by jslim22 - 07-14-2006, 12:59 PM

[No subject] - by planigan - 07-16-2006, 10:29 PM

Stuffing the can? - by jslim22 - 07-19-2006, 03:11 PM

[No subject] - by 49Stude63 - 07-19-2006, 03:23 PM

Electrolytic stuffing. - by planigan - 07-19-2006, 11:59 PM

Stuffing cans - by planigan - 07-20-2006, 12:26 AM

Thanks to both - by jslim22 - 07-23-2006, 02:09 AM

Electorlytic Stuffing - by planigan - 07-23-2006, 11:33 PM

Cutting the wrong end of the cap - by jslim22 - 07-24-2006, 11:10 PM

Cutting the wrong end of cap - by planigan - 07-24-2006, 11:50 PM

Hi Pat - by jslim22 - 07-27-2006, 10:02 AM

[No subject] - by planigan - 07-27-2006, 12:22 PM

Thanks as always - by jslim22 - 07-28-2006, 03:38 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

Who's Online
There are currently no members online.