Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

116x Rectifier light show
#3

A failed electrolytic was the problem. Radio up and running now. My only issue is lots of noise which sounds like interference when moving across the am band. It makes it difficult to hear weaker stations. Also loud popping when switching between bands. I have tried moving wires around under chassis with no improvement. Any suggestions, as always thanks so much for the help. Gary


Messages In This Thread
116x Rectifier light show - by garyh1 - 09-13-2011, 11:50 PM
Re: 116x Rectifier light show - by codefox1 - 09-14-2011, 09:10 AM
Re: 116x Rectifier light show - by garyh1 - 09-17-2011, 10:32 AM
Re: 116x Rectifier light show - by TA Forbes - 09-17-2011, 12:25 PM
Re: 116x Rectifier light show - by garyh1 - 09-17-2011, 07:16 PM
Re: 116x Rectifier light show - by garyh1 - 09-17-2011, 07:38 PM
Re: 116x Rectifier light show - by Marsupial - 09-18-2011, 01:07 AM
Re: 116x Rectifier light show - by garyh1 - 09-18-2011, 01:29 AM
Re: 116x Rectifier light show - by garyh1 - 09-18-2011, 03:04 AM
Re: 116x Rectifier light show - by garyh1 - 09-18-2011, 03:06 AM
Re: 116x Rectifier light show - by Ron Ramirez - 09-18-2011, 07:05 AM
Re: 116x Rectifier light show - by garyh1 - 09-18-2011, 11:41 AM
Re: 116x Rectifier light show - by TA Forbes - 09-18-2011, 04:55 PM
Re: 116x Rectifier light show - by Ron Ramirez - 09-18-2011, 04:56 PM
Re: 116x Rectifier light show - by TA Forbes - 09-18-2011, 07:03 PM
Re: 116x Rectifier light show - by thirtiesradio - 09-19-2011, 02:35 AM
Re: 116x Rectifier light show - by Glenn Roberts - 09-19-2011, 04:15 AM
Re: 116x Rectifier light show - by codefox1 - 09-19-2011, 10:43 AM
Re: 116x Rectifier light show - by garyh1 - 09-19-2011, 01:29 PM
Re: 116x Rectifier light show - by TA Forbes - 09-19-2011, 01:53 PM
Re: 116x Rectifier light show - by thirtiesradio - 09-20-2011, 12:18 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM
Philco model 38 code 121 not receiving signal.
Well why not! :lol:Stormlord5500 — 03:14 PM

[-]
Who's Online
There are currently no members online.

>