PHILCO 37-660

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12, 2025) x

Linear Mode

PHILCO 37-660

georgetownjohn
Member

Posts: 89
Threads: 17
Joined: Nov 2024
City: GEORGETOWN, Texas State, Province, Country: United States

#26

06-15-2026, 06:28 PM

Morzh, thanks as always for the saftey cap info. Thanks to Roy for the reply, yes, I measured the hole and found that Rnovated Radios part CH4 should be the one so I ordered 4 of them. The one that has a screw and sleeve in it that goes in the bottom center rear of the wood cabinet and then up through the chassis is still good so I am ok there.,, John

Find

« Next Oldest | Next Newest »

Messages In This Thread

PHILCO 37-660 - by georgetownjohn - 06-10-2026, 04:15 PM

RE: PHILCO 37-660 - by morzh - 06-10-2026, 04:39 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-10-2026, 05:03 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-11-2026, 06:18 PM

RE: PHILCO 37-660 - by morzh - 06-11-2026, 09:32 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-12-2026, 04:08 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-12-2026, 04:14 PM

RE: PHILCO 37-660 - by morzh - 06-12-2026, 04:49 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-12-2026, 06:44 PM

RE: PHILCO 37-660 - by Arran - 06-12-2026, 07:50 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-12-2026, 08:05 PM

RE: PHILCO 37-660 - by morzh - 06-12-2026, 08:22 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-12-2026, 08:40 PM

RE: PHILCO 37-660 - by radiorich - 06-12-2026, 10:36 PM

RE: PHILCO 37-660 - by MrFixr55 - 06-12-2026, 10:39 PM

RE: PHILCO 37-660 - by Arran - 06-13-2026, 01:31 AM

RE: PHILCO 37-660 - by MrFixr55 - 06-13-2026, 06:52 AM

RE: PHILCO 37-660 - by georgetownjohn - 06-13-2026, 01:58 PM

RE: PHILCO 37-660 - by morzh - 06-13-2026, 06:20 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-14-2026, 01:58 PM

RE: PHILCO 37-660 - by Joe Rossi - 06-14-2026, 02:42 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-15-2026, 02:48 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-15-2026, 02:57 PM

RE: PHILCO 37-660 - by morzh - 06-15-2026, 03:43 PM

RE: PHILCO 37-660 - by glyphmon - 06-15-2026, 03:53 PM

RE: PHILCO 37-660 - by georgetownjohn - 06-15-2026, 06:28 PM

RE: PHILCO 37-660 - by radiorich - 07-04-2026, 12:55 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 71 Code 125
Looks like that might be the B- buss, so that would be correct.RodB — 01:32 PM
Philco 71 Code 125
I noticed on the code 121 schematic the center tap for the 6 volt winding and hv winding are tied together. Is this corr...dconant — 12:16 PM
Philco 45-6365 Universal IFT Instruction Manual
The Philco Parts Catalog for 1942 shows it as usable for 175 kHz, 260 kHz, and 465 kHz. The instructions will show how t...DaleHCook — 11:19 AM
Stromberg Carlson 1500 Squeal
Hello Rob, I agree with you—I have one here at my house that I need to check out. It’s way over-engineered just to make...radiorich — 11:05 AM
My Atwater Kent 84
Well getting around to restoring my AK84. Mike was a big part in me being able to snatch this one a few years ago. I won...462ron — 10:57 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
The engine is a B&S 23 inch cast Iron holds 2 quarts of oil. The Generator is a 4 pole 1800 rpm mine was made in 195...David — 10:51 AM
Philco 45-6365 Universal IFT Instruction Manual
Dale: Modified topic as suggested. It is not for a specific project. I found it in a box of stuff I recently purchased...GRG — 10:34 AM
Plug Voltages Needed For A 1943 CRV-20130 Power Supply
That looks a lot like an aircraft connector of some kind ... That is a MIL-5015 style connector, used in a wide v...DaleHCook — 10:19 AM
Philco P45-6365 Universal Transformer Instruction Manual
I would suggest changing the topic from "P45-6365 Universal Transformer" to "45-6365 Universal IFT."...DaleHCook — 10:08 AM
Stromberg Carlson 1500 Squeal
And life just keeps getting more complicated. By dconant. Dittos'Jimradio — 08:01 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me